Graco XD30 Series Instructions Manual Download

Page: 5 / 10

Warnings

3A0142A

12. Remove nut (40) and bolt (43), bushing (41), pawl

(42) and spring (44) from arm (F

. 8). Discard

these parts. Use new parts included in the kit for
reassembly.

13. Remove screws (48) and ratchet (59) from spool.

. 9). Discard these parts. Use new parts

included in the kit for reassembly.

Reassembly

Install new pawl (42), bushing (41), spring (44),
nut(40) and bolt (43) to guide arm (30). Tighten bolt
securely (F

. 10).

Place spool (9) on its side on a work bench (F

11).

NOTE:

It is easier to reattach the guide arm and

pedestal assembly to the spool if the spool is sup-
ported and somewhat level. Placing a couple blocks
of 1” thick scrap wood under the spool as shown in
F

. 11 will help support the spool during the arm

installation.

. 8

. 9

41/42

. 10

. 11

41/42

Summary of Contents for XD30 Series











Search results

Summary of Contents for XD30 Series

Reviews:

Related manuals for XD30 Series

Brands by name

Popular brands

Graco XD30 Series, Instructions Manual

Search results

Summary of Contents for XD30 Series

Reviews:

Related manuals for XD30 Series

Brands by name

Popular brands