Gradall D152 Operators Safety Manual Download

Page: 69 / 98

Section 3 - Operation

3-19

82104002

3.7

LIFT CAPACITY

Note: This is a sample capacity chart only! DO NOT use this chart, use the one
located in your operator cab.

OAC0690

LOAD POINT HEIGHT

ABOVE

GROUND

LEVEL

BELOW

GROUND

LEVEL

LOAD RADIUS

AT GROUND LEVEL

OVER

END

OVER

SIDE

10’ (3.0m)

OVER

END

OVER

SIDE

15’ (4.6m)

OVER

END

OVER

SIDE

20’ (6.1m)

OVER

END

OVER

SIDE

25’ (7.6m)

MAXIMUM

RADIUS

OVER

END

OVER

SIDE

20’ (6.1m)

15’ (4.6m)

10’ (3.0m)

8’ 7” (2.4m)

5’ (1.5m)

BOOM LEVEL

20’ (6.1m)

15’ (4.6m)

10’ (3.0m)

5’ (1.5m)

8500

(3855)

5840

(2650)

8500

(3855)

5840

(2650)

12425
(5635)

11090

(5030)

8630

(3915)

6640

(3010)

11090
(5030)

8630

(3915)

6640

(3010)

8795

(3990)

9880

(4480)

10080
(4570)

10290
(4665)

9815

(4450)

8705

(3950)

7365

(3340)

6075

(2755)

8795

(3990)

9880

(4480)

10080
(4570)

8705

(3950)

7365

(3340)

6075

(2755)

10030
(4550)

9800

(4445)

5715

(2590)

6515

(2955)

7140

(3240)

7255

(3290)

7415

(3365)

7265

(3295)

6745

(3060)

6010

(2725)

5715

(2590)

6515

(2955)

7140

(3240)

7255

(3290)

6745

(3060)

6010

(2725)

7175

(3255)

7035

(3190)

27’ 4”

(8.3m)

29’ 5”

(9m)

30’ 6”

(9.3m)

30’ 7”

(9.3m)

30’ 7”

(9.3m)

29’ 11”

(9.1m)

28’ 3”

(8.6m)

25’ 5”

(7.7m)

20’ 11”

(6.4m)

12’ 10”

(3.9m)

5070

(2300)

5120

(2320)

5230

(2370)

5265

(2390)

5070

(2300)

5120

(2320)

5230

(2370)

5265

(2390)

5375

(2440)

5550

(2515)

5740

(2605)

5195

(2355)

5310

(2410)

5725

(2595)

5910

(2680)

5930

(2690)

4875

(2210)

5910

(2680)

5930

(2690)

4875

(2210)

The above loads are in compliance with the SAE standard
J1097 DEC2005. They do not exceed 87% of hydraulic
lifting capacity or 75% of tipping capacity.

Loads shown in shaded areas indicate the load is
limited by tipping rather than hydraulic lift capacity.

The rated lift capacity is based on the machine being
equipped with 15,500 lb (7030 kg) counterweight, standard
boom, standard tires, no auxiliary hydraulics, and no bucket.

Adjust the listed rated capacities by subtracting the value
listed for bucket/attachment used:

8065-6007 60” (1.5 m)
8065-6006 66” (1.7 m)
8065-6002 72” (1.8 m)
8045-6020 24” (610 mm)
8045-6021 30” (762 mm)
8045-6022 36” (914 mm)
8045-6023 42” (1.1 m)
8045-6024 48” (1.2 m)
8065-6013 72” (1.8 m)
8065-6102 40” (1.0 m)
8065-6024 8’ (2.4 m)
8065-6009 Single Tooth Ripper -

Ditching -
Ditching -
Ditching -
Excavating -
Excavating -
Excavating -
Excavating -
Excavating -
Dredging -
Pavement -
Blade -

807 lbs. (366 kg)
892 lbs. (405 kg)
944 lbs. (428 kg)
603 lbs. (274 kg)
660 lbs. (300 kg)
741 lbs. (336 kg)
841 lbs. (382 kg)
957 lbs. (434 kg)
1114 lbs. (505 kg)
1262 lbs. (573 kg)
630 lbs. (285 kg)
557 lbs. (253 kg)

The load point is located on the bucket pivot point,
including loads listed for maximum radius.

Do not attempt to lift or hold any load greater than these
rated values at specified load radii and heights. The weight
of slings and any auxiliary devices must be deducted from
the rated load to determine the net load that may be lifted.

ATTENTION: All rated loads are based on the machine
being stationary and level on a firm supporting surface.
The user must make allowance for particular job conditions
such as soft or uneven ground, out of level conditions, side
loads, hazardous conditions, experience of personnel, etc.
The operator and other personnel must read and understand
the operator manual before operating this machine. Rules
for safe operation of equipment must be adhered to at all
times.

Note: Bucket adjustment values are 87% of the actual bucket weights.