background image

F

I S H E R M A N

  2 0 9

8–9

T

RIM

 T

ABS

Trim tabs are electrically and hydraulically operated. The trim tab system includes a hydraulic 

pump, a switch with an integrated indicator, and an auto-retract feature. The switch controls the 
pump which lowers and raises the trim tabs. The indicator keeps you constantly aware of the trim 
tab’s position. The auto-retract feature automatically raises the tabs every time the ignition switch 
is turned off.

Trim tabs are used to regulate the attitude of the boat while moving. They are operated by a 

two-rocker switch panel and will aid in trimming the boat fore and aft for a smoother ride. Trim 
tabs can improve the ride of your boat by adjusting where the water is hitting the keel line. In a 
slight chop, the waves may be hitting the keel of your boat around the helm area causing an 
uncomfortable ride. By adjusting the trim tabs and lowering the bow, the waves will hit the keel at 
a more forward point and soften the ride. Experimenting with trim tabs in various sea conditions 
will help you determine the best positions for your boat under different load conditions.

Trim tabs are also useful in correcting a port or starboard running list. If the boat is listing to 

the port side, press the starboard trim tab switch toward “bow down”. Press the port trim tab 
switch toward “bow down” to correct a starboard list. This will tend to lower the bow by pulling 
the higher side to a level position. If your bow is already in a low position and your tabs are down, 
you may correct a listing condition by pressing the trim tab switch toward “bow up”. This will 
cause the low side to rise and level the boat. The running angle will also gradually improve.

Trim tabs in the extreme “bow up” positions will have no effect on the boat's ride. Trim tabs in 

the extreme “bow down” position will cause the boat to come on plane with minimum bow rise. 
Unless you are operating at low speeds or with considerable cockpit weight you will likely want 
to raise the tabs slightly when underway to avoid “plowing” water. With the tabs in the “bow 
down” position, you will be able to maintain a plane at the least possible RPMs.

Trim Tab Pump Location

The trim tab pump is located inside the center console storage area. The hydraulic fluid level 
should be checked on a seasonal basis.

Summary of Contents for Fisherman 209













































































Reviews: