background image

 
 

12 / 18 

9. 

Minimax Filter Package Installation 

 

10.  Inspection and servicing 

 

9.1. Minimax Internal Filter 

• The Filter Package is supplied with Filter Body, Filter Basket,  
Spray Cleaner, Two Spannfix Collars, Emergency Overflow Siphon,  
Rodent Guard, Settled Inlet Connection, One 150mm Rubber Ring  
Adaptor  and One 250mm Rubber Ring Adaptor  
•The filter has a built in difference between inflow/outflow of 10mm. 
• The filter is suitable for roof areas up to 350 square metres. 
• The mesh width in the sieve insert is 0.35mm. 

 

9.2. Technical Specifications 

 
 
 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
9.3 Installation of inflow pipe and overflow siphon 

The emergency overflow siphon (pictured at top on page on the left and on Page 13) is installed at 90 
degrees to the inlet and outlets of the tank; the Rodent Guard is inserted in the opening of the trap. 
 

 
9.4 Filter Installation 

Connect the filter body into the bell end of 100 mm PVC pipe. Having already cut the pipe to the required 
length connect it with the inlet stilling system ensuring it is firmly in place. 

 

 

 

Flow 

Overflow Siphon/Skimmer 

Summary of Contents for PLATIN



















Reviews: