background image

10

8

Err  11

Load-cell problem

9

Err  13

Resolving capability is too high

10

Err  14

Damaged inside indicator

11

Loch

Overload and locked

RECHARGEABLE LITHIUM BATTERY

Battery inside of scale is Lithium battery. Please charge it after running 
down for 7 hours the first three times. Please charge the battery for timing 
if not use it often. 

The battery is an easily exhausted product. And it is not granted free 
guarantee. 

MAINTENANCE

1.  To guarantee indicator clarity and using life, the indicator shouldn’t be 

placed directly under sunshine and should be set in the plain space.

2.  The indicator can’t be placed into the place where the dust pollution and 

vibration are serious.

3.  Load cell should connect with indicator reliably, and the system should 

be well connected into ground. The indicator must be protected from 
high electrical field and high magnetic field.
In order to protect the operator, indicator and relevant device, you should 
mount lightning rod in thunderstorm frequently happening area.

•  Load cell and indicator are static sensitive device, you must adopt 

anti-static measures.

4.  It is strictly forbidden to clean the case of indicator with intensive solvents 

(for example: benzene and nitro oils).

Summary of Contents for C6-10T

















Reviews: