background image

Voice Broadband Optical Multiplexer 

User 

Manual 

 

11 

 
11.  Do  not  point  the  optical  header  toward  eyes,  lest  that  laser  injures  the 
retina. 
 

4.2 Inspection upon Unpacking 

After unpacking the product, inspect the type, quantity and condition of 

device  and  accessories  inside  according  to  the  list  of  contents  specified  in 
this  manual.  Contact  the  Company  or  its  distributors  and  agencies 
immediately should abnormal circumstances arise. 

 

4.3 Power Supply 

Check  the  power  supply  of  the  device.  The  power  input 

should  be  configured  in  accordance  with  related  requirements. 
Pay  particular  attention  to  the  voltage  and  polarity  if  the  power 
supply  is  DC. 

Before  you  plug  and  unplug  the  power  cable, 

please  disconnect  the  power  supply.  Connect  the  power 
supply  again  after  operation.  And  use  the  equipment  under 
the operating condition required in the manual. 

 

4.4 Test 

The following tests should be conducted before use: 
1.  After  the  device  is  powered  up  correctly,  check  whether 

PWR,  LOS,  E1L1, E1L2, E1L3, E1L4  and  SYS are  on,  and  the 
rest LED indicators are off. 

 

4.5 Configuration and Connection 

If indicators work correctly as described in 5.4, turn off the 

power,  configure  operating  modes  based  on  the  overall 
requirements  of  network  environment,  plug  on  E1  cable  and 
optical fibers, and then turn on the power. The device will enter 
into normal operation. 

 
If the device fails to work properly as described in 4.4, see 

failure  diagnoses  and  troubleshooting  section  of  the  manual.  If 
the failure still exists, contact the Company or its distributors and 
agencies immediately. 
 

Summary of Contents for OP-4E1+ETH+32Vo


















Reviews: