86
Ground Control 3.0 Manual
Rev: 06.28.18
Page 10
CCD-0001519
Unhitching Instructions
NOTE:
Prior to unhitching from the tow vehicle, ensure trailer is parked on a level surface
and chock the tires of the
trailer.
1.
Extend the inner legs of both front jacks (landing gear)to within 4-5" of the ground
by pulling on the quick-release pins.
2.
Open the OneControl App.
3.
Press the "Leveler" icon.
4.
The screen will show the system menu (Fig. 4) for Standard Mode.
5.
Push "Extend" (Fig. 4I) and "FRONT" buttons (Fig. 4) to extend front jacks and lift front of trailer
to take the
weight of the trailer off of the hitch.
6.
Uncouple the trailer connection on the tow vehicle.
7.
Pull tow vehicle away and park at a safe distance.
Auto Level
1.
After unhitching from the tow vehicle and parking the vehicle at a safe distance away from the trailer,
open
the OneControl App and then press “AUTO LEVEL” (Fig. 4J).
NOTE:
Once the automatic leveling cycle has been started, it is important that there is no movement in the trailer
until the trailer has completed the leveling process. Failure to remain still during the leveling cycle could
have an effect on the performance of the leveling system.
Auto Level Sequence
1.
When Auto Level Sequence begins, the front of the trailer will seek a position near a level state.
2.
Rear jacks will be grounded.
3.
A side-to-side leveling sequence will occur.
NOTE:
At this point on the 6 point system, the 2 middle jacks will be grounded to stabilize the trailer.
These 2 jacks do not level the trailer.
4.
Each jack will perform a final grounding touch.
NOTE:
If the AUTO LEVEL sequence does not perform as described above, locate the OneControl Touch Panel
inside the trailer or use the OneControl App to place the system in manual mode. Test that the jacks
operate correctly by pushing their corresponding buttons on the OneControl Touch Panel or App;
e.g., "FRONT" button operates only the front jacks, etc. (See "Operation - OneControl Touch Panel" or
"Operation - OneControl App" in this manual).
Hitch Recognition
1.
Open the OneControl App.
2.
Press the "Leveler" icon.
3.
The screen will show the system menu (Fig. 4) for Standard Mode.
4.
Press "AUTO HITCH" (Fig. 4K). Rear jacks will retract.
5.
The front of the trailer will raise to the height where the auto level sequence was started.
NOTE:
If the front of the trailer was below level when the Auto Level process was initiated, the hitch recognition
feature will retract the rear jacks but will not retract the front jacks to lower the trailer to the initial hitch
height. This feature helps prevent injury and/or damage to anything underneath the trailer.
6.
Connect tow vehicle and make sure trailer and hitch are connected and locked.
7.
On the Standard Mode screen (Fig. 4) use the "UP" and "DOWN" arrows (Fig. 4G) to scroll to "AUTO RETRACT"
(Fig. 4D). Press "ENTER."
8.
Choose "ALL JACKS." Press “ENTER." System will immediately retract all jacks.
Use the quick release pins on the landing gear to manually return the inner jack leg to the fully retracted position.
NOTE:
If the rear jacks will not operate individually using the method described above, but they operate
properly when Auto Level is performed, the Twist Prevention Protection system has locked out the
operation to prevent damage to the frame of the trailer.
Summary of Contents for Reflection Fifth Wheel 150 Series
