background image

 

 

 

MST-91Ai   Installation guide EN Rev 1.0 

14

 

Warranty Terms 

 
The manufacturer guarantees that the product meets the specifications specified in the Installation 
Manual.

 

Warranty period - 3 (three) years from the date of sale.

 

The manufacturer’s warranty provides for free repair or replacement of the product during the entire 
warranty period, subject to the following conditions: 

• the product was used for its intended purpose; 

• installation and operation of the product was carried out in accordance with this Installation Guide 
and the Operation Manual; 

• the product does not have mechanical damage that caused malfunctions (including, but not limited 
to: liquids, breaks, chips, cracks in the product); 

• the rules and requirements for transportation and storage of the product have been complied with; 

• A Warranty Certificate is filled out with the name of the organization and the seller’s stamp; 

• If at the time of diagnosis or after it is established that any of the listed conditions is not met, the 
Manufacturer  or  his  representative  has  the  right  to  refuse  warranty  service,  having  issued  an 
appropriate conclusion. 

The  product  is  withdrawn  from  the  warranty  and  free  repair  /  replacement  of  the  product  is  not 
performed in the following cases: 

• the warranty has expired. 

• the product was damaged during transportation after receiving the goods or storage, in case if the 
product was not put into operation; or the rules for installation and operation, transportation and 
storage were violated. 

 

 
 
 

 

 

 

 

 

 

 

Summary of Contents for MST-91Ai

















Reviews: