Grandstream Networks GXP1610 Administration Manual Download

Page: 35 / 49

GXP1610/GXP1620/GXP1625/GXP1628

Administration Guide

Page 34 of 48

default, it is set to "DHCP".

Host name (Option 12)

Specifies the name of the client. This field is optional but may be required by
some Internet Service Providers.

Vendor Class ID
(Option 60)

Used by clients and servers to exchange vendor class ID.

PPPoE Account ID

Enter the PPPoE account ID.

PPPoE Password

Enter the PPPoE Password.

PPPoE Service Name

Enter the PPPoE Service Name.

IPv4 Address

Enter the IP address when static IP is used.

Subnet Mask

Enter the Subnet Mask when static IP is used for IPv4.

Gateway

Enter the Default Gateway when static IP is used for IPv4.

DNS Server 1

Enter the DNS Server 1 when static IP is used for IPv4.

DNS Server 2

Enter the DNS Server 2 when static IP is used for IPv4.

Preferred DNS Server

Enter the Preferred DNS Server for IPv4.

IPv6 Address Type

Allows users to configure the appropriate network settings on the phone to
obtain IPv6 address. Users could select "Auto-configured" or "Statically
configured" for the IPv6 address type.

Static IPv6 Address

Enter the static IPv6 address when Full Static is used in "Statically configured"
IPv6 address type.

IPv6 Prefix Length

Enter the IPv6 prefix length when Full Static is used in "Statically configured"
IPv6 address type.

IPv6 Prefix

Enter the IPv6 Prefix (64 bits) when Prefix Static is used in "Statically
configured" IPv6 address type.

DNS Server 1

Enter the DNS Server 1 for IPv6.

DNS Server 2

Enter the DNS Server 2 for IPv6.

Preferred DNS server

Enter the Preferred DNS Server for IPv6.

Network -> Advanced Settings

802.1X mode

Allows the user to enable/disable 802.1X mode on the phone. The default
value is disabled. It can be set to EAP-MD5, EAP-TLS or EAP-
PEAPv0/MSCHAPv2.

802.1X Identity

Enter the Identity for the 802.1X mode.

MD5 Password

Enter the MD5 Password for the 802.1X mode.

802.1X CA Certificate

Upload 802.1X CA certificate to the phone; or delete existed 802.1X CA
certificate from the phone.

802.1X Client Certificate

Upload 802.1X Client certificate to the phone; or delete existed 802.1X Client
certificate from the phone.

HTTP Proxy

Specifies the HTTP proxy URL for the phone to send packets to. The proxy
server will act as an intermediary to route the packets to the destination.

HTTPS Proxy

Specifies the HTTPS proxy URL for the phone to send packets to. The proxy
server will act as an intermediary to route the packets to the destination.

Layer 3 QoS

Defines the Layer 3 QoS parameter. This value is used for IP Precedence,
Diff-Serv or MPLS. The default value is 12.

Layer 2 QoS
802.1Q/VLAN Tag

Assigns the VLAN Tag of the Layer 2 QoS packets. The default value is 0.

Layer 2 QoS 802.1p
Priority Value

Assigns the priority value of the Layer2 QoS packets. The default value is 0.

PC Port Mode

Configures the PC port mode. When set to "Mirrored", the traffic in the LAN
port will go through PC port as well and packets can be captured by

Summary of Contents for GXP1610


















































Search results

Summary of Contents for GXP1610

Reviews:

Related manuals for GXP1610

Brands by name

Popular brands

Grandstream Networks GXP1610, Administration Manual

Search results

Summary of Contents for GXP1610

Reviews:

Related manuals for GXP1610

Brands by name

Popular brands