background image

 

2635 W. 7

th

 Place, Eugene, Oregon 97402, USA  

6  

Valid from February 2017 

 

 

 

www.grapesolar.com 

 

6 Tel: 1-877-264-1014 (toll free), 1-541-349-9000, Fax: 1-541-343-9000 

 

 

 

 

 

 

 

PHOTOVOLTAIC MODULES SAFETY 

 

AND INST

 

ALLATION MANUAL Rev. 

 

P

 

 

 

VALID IN NORTH AMERICA ONLY

 

 

 

 

 

 

 

3.10 PV modules do not have a power ON/OFF switch. The only way to make modules inoperative is 

removing them from light, or fully covering their front surface with an opaque material, or 
placing modules face down on a smooth, flat surface.  

3.11 Avoid setting the module down with any type of force on any surface, particularly when placing 

it at a corner.  

3.12

 

To prevent untrained personnel from disconnecting the modules after installed, locking 

connectors and safety clips must be used in the installation.   

3.13

 

Do not touch electrical terminals or the ends of any wire while installing the module. Do not open 

electrical connections or unplug connectors while the PV system circuit is under load.

 

Contact 

with electrically active parts of the modules, such as terminals, can result in burns, sparks and 
lethal shock whether the module is connected or disconnected.  

3.14

 

Cover all modules in the PV array with an opaque cloth or material before making or breaking 

electrical connections.  

3.15

 

Broken junction boxes or broken connectors are electrical and laceration hazardous and cannot be 

repaired. Please contact the installers to remove the broken module from the array and contact 
the supplier for disposal instructions.  

4.

 

Fire Safety  

 

4.1   Grape Solar’s PV modules are non-explosion-protected equipment and fire rated Type 1 or Type 

2 (see panel spec sheet).  

4.2   Building fire safety may be affected by installing a PV system. Improper installation may lead to 

hazards in the event of fire. Refer to local authority for guidelines and requirements for building 
or structural fire safety.  

4.3   For roof installation, PV modules should be mounted over a fire resistant covering which is 

rated for the application.  

4.4   Do not install modules near equipment or locations where flammable gases can be generated or 

collected.  

4.5   Grape Solar recommends using components such as earth ground fault circuit breakers, fuses 

and circuit breakers in the PV system for fire prevention.  

Summary of Contents for GS-M60-285-Fab1-US













Reviews: