A-14
A.5
Initial Setting
Menu items
Setting item
Initial value
TOOLS SETTING
(TOOL)
TOOL OFFSET ADJ.
–
STEP PASS
1
OFFSET FORCE
–
OFFSET ANGLE
30
DATA SORTING
ON
CONDITION PRIORITY
PROGRAM
TOOL UP MOVE
DISABLED
MOVING SPEED
AUTO
TOOL UP HEIGHT
NORMAL POSITION
BLADE WEAR ALARM SETUP
OFF
INITIAL B. ANGLE POSITION
2mm BELOW
AXIS SETTING
(AXIS)
AXIS SETTING
OFF
AREA PARAMETERS
(AREA)
AREA SET LOWER LEFT
(DEFAULT)
AREA SET UPPER RIGHT
(DEFAULT)
EXPAND
(DEFAULT)
ROTATE
OFF
MEDIA SETTING
(MEDIA)
'F'COMMAND CUT
OFF
AUTO PRE FEED
OFF
AUTO PRE FEED FEED LENGTH
1m
PAGE LENGTH
300.0cm
INITIAL FEED
OFF
FEED SPEED
NORMAL POSITION
CROSS CUT FORCE
20
PANEL CUTTING
OFF
DIVIDE LENGTH
100.0cm
CROSS CUT
ON
SPACE REAR
70mm
PAPER LOAD FUNCTION
2
PAPER READY TIME
180sec
INTERFACE
(I/F)
COMMAND
HP-GL
HP-GL ORIGIN POINT
LOWER LEFT
HP-GL MODEL EMULATED
7586
GP-GL STEP SIZE
0.100mm
RS-232C (SWITCHING SETTING NUMBERS)
No.1
RS232C: FORWARDING CONDITION
BAUD RATE/DATA BIT/
PARITY/HARDWIRE HANDSHAKE
RS-232C No.1 : 9600/8/NONE//HARD
RS-232C No.2 : 9600/7/EVEN//HARD
RS-232C No.3 : 9600/8/EVEN/XonXoff
RS-232C No.4 : 9600/8/EVEN/XonXoff
LAN DHCP
OFF
LAN IP
192.168.0.1
LAN SUBNET MASK
255.255.255.0
LAN GATEWAY
192.168.0.254
COMMAND ':',';'
ENABLED
COMMAND 'W'
TOOL UP
CIRCLE RESOLUTION
DEFAULT
ADVANCE
(ADV.)
MOVE STEP
0.1mm
LANGUAGE SELECTION
Select when initially turning on power
LENGTH UNIT
Select when initially turning on power
BEEP FOR KEY OPE.
ON
POSI. KEY SPEED + SLOW KEY
1cm/s
POSI. KEY SPEED
10cm/s
PAUSE/MENU KEY SETTING
PAUSE
LCD CONTRAST
0
MEDIA SENSOR
ENABLED
PUSH ROLLER SENSOR
ENABLED
FAN POWER
NORMAL POSITION
TEST
(TEST)
NO SETTINGS
–
Summary of Contents for CE7000-130AP
