FC8600-UM-251-9370 3-1
3 OPERATIONS
3 OPERATIONS
3.1 Control Panel
This section explains the function of lamps and keys on the control panel.
USER1 lamp
USER2 lamp
[1] key
[2] key CROSS CUT
key
MENU lamp
[MENU] key
[STOP] key
[ORIGIN] key
[ENTER] key
[CONDITION]
key
POSITION
[FAST] key
[3] key
[4] key
[COPY] key
Screen (LCD)
Control Keys
POSITION keys .............. There are following functions depending on the operation. Move the tool carriage
and media. It will move specified distance when it is pressed once,and continuously
move when it is pressed down. It will select the menu when UP, DOWN, LEFT or
RIGHT arrow keys are displayed in the menu on the screen.
FAST ............................... The tool carriage or the media will move faster when it is pressed simultaneously
with POSITION key. It will work as a menu key when it is displaying “F” on the
screen.
CROSS CUT .................. It will cut off the media that has finished cutting.
STOP .............................. Cutting operation will stop immediately when the [STOP] key is pressed while
cutting.
You can reset the media by pressing the [STOP] key while cutting when the media
has shifted.
ORIGIN ........................... It will set the current position as an origin point.
The plotter is reset by pressing the [ENTER] key and the [ORIGIN] key
simultaneously in the first screen of the MENU mode (MENU screen).
Menu Keys
MENU ............................. It will switch to the MENU mode. MENU lamp is lit in the MENU mode.
It will go into MENU mode if it is pressed once, and MENU mode will be turned off
when it is pressed again.
Different function are set in the MENU mode.
Data received while in the MENU mode will be stored in the data buffer.
CONDITION ................... It will display the screen to set the tool conditions.
1, 2, 3, 4.......................... Select the menu number displayed in the screen.
ENTER ........................... It will define the settings. The plotter is reset by pressing the [ORIGIN] key and this
key simultaneously in the first screen of the MENU mode (MENU screen). It will
display current cutting area when the [ENTER] key is pressed in READY status.
Summary of Contents for FC8600-100
