background image

 

Contacting Grass Valley Group

 

Copyright © Grass Valley Group. All rights reserved.

This document may not be copied, in whole or in part, or otherwise reproduced, except as specifically 
permitted under U.S. copyright law, without the prior written consent of Grass Valley Group, P.O. Box 
599000, Nevada City, CA 95959-7900 USA. GRASS VALLEY GROUP is a registered trademark and 
Grass Valley is a trademark of Grass Valley Group. All registered trademarks and trademarks are prop-
erty of their respective holders. Grass Valley Group products are covered by U.S. and foreign patents, 
issued and pending. Product options and specifications subject to change without notice. The informa-
tion in this manual is furnished for informational use only, is subject to change without notice, and 
should not be construed as a commitment by Grass Valley Group. Grass Valley Group assumes no re-
sponsibility or liability for any errors or inaccuracies that may appear in this publication.

 

Region

Voice

Fax

Address

Web Site

 

North America

(800) 547-8949
530-478-4148

(530) 478-3347

Grass Valley Group
P.O. Box 599000
Nevada City, CA 95959-7900 
USA

www.grassvalleygroup.com

Pacific Operations

+852-2585-6688
Support: 852-2585-6579

+852-2802-2996

U.K., Europe, Asia, Middle East

+44 1753 218 777

+44 1753 218 757

France

+33 1 45 29 73 00

Germany

+49 221 1791 234

+49 221 1791 235

Summary of Contents for 8911 AES-EBU

















Reviews: