GRASS VALLEY CameraMan 2018 Installation And Operation Manual Download

Page: 26 / 35

Page 23

The Camera Setup Mode buttons (with green text) on your keypad allow you to adjust the cameras settings via four on-screen

menus. These adjustments should be made by qualified technical personnel only.

Important Note:

If your system includes a CameraMan SHOT Director, make these adjustments only with the SHOT Director. Do

not use the Keypad.

Adjusting the Camera Setup Mode Settings

SETUP and MODE Buttons

To enter the camera setup mode:

Press and hold the SETUP and MODE buttons simultaneously for 2.5 seconds. The

keypad should beep once.

Release both buttons.
The camera will flash, and an on-screen menu will appear when it enters the camera

setup mode.

MENU EDIT arrows

To select a setting, or the value of a setting, use the PAN/TILT MENU EDIT left/right, and

up/down arrows on your keypad.

tilt UP: moves the on-screen cursor up.
tilt DOWN: moves the on-screen cursor down.
pan RIGHT: increases, or changes the setting.
pan LEFT: decreases, or changes the setting.

To change between the various on-screen settings menus:

Place the cursor on the first line of the menu using the menu edit UP and DOWN

arrows.

Select the menu page (1-4) using the menu edit LEFT and RIGHT arrows.

For more information on the on-screen camera settings and their functionality,

refer to the CameraMan installation and operations manual that came with your

camera.

When accessing the on-screen camera settings, do not change the BAUD RATE

as this may impact the cameras communication links.

MENU Button

Press the Menu button to toggle between the on-screen settings menu and the video image.

BARS Button

Press the Bars button to toggle between the on-screen color bars and the video image.

White Balance Button

Press the button next to the W to automatically set the white balance in the camera setup

mode.

Once all adjustments have been made, the camera must be returned to the system mode for

normal operation. Just follow the same directions to enter camera setup mode (listed above).

MENU button

MENU EDIT arrows

SETUP button

MODE button

BARS button

WHITE BALANCE button

Summary of Contents for CameraMan 2018




































Search results

Summary of Contents for CameraMan 2018

Reviews:

Related manuals for CameraMan 2018

Brands by name

Popular brands

GRASS VALLEY CameraMan 2018, Installation And Operation Manual

Search results

Summary of Contents for CameraMan 2018

Reviews:

Related manuals for CameraMan 2018

Brands by name

Popular brands