background image

BVS-1602  

Rev. 2

 

 
 

12 

 

8.5 Commands 

 

8.5.1  Audio crosspoint set  

Only for use with Audio routers. 
Command for setting of crosspoints: 
 

 

 

 

1001nnnn  

0kkk kkkk  

0vvv vvvv 

 
 

 

- nnnn is the matrix address from 0 up to 15. 

 

 

- kkk kkkk is the output which shall be controlled.  

 

 

 

kkk kkkk = output number    

   0 

output 

   127 

output 

128 

 
 

 

- vvv vvvv is the input which shall be connected to the chosen output.  

 

 

 

vvv vvvv = input number 

 
8.5.2  Audio crosspoint set acknowledge  

Only for use with Audio routers. 
Command for acknowledging setting of crosspoints: 
 

 

 

 

1000nnnn  

0kkk kkkk  

0vvv vvvv 

 
 

 

- nnnn is the matrix address from 0 up to 15. 

 

 

- kkk kkkk is the output which shall be controlled.  

 

 

 

kkk kkkk = output number    

   0 

output 

   127 

output 

128 

 
 

 

- vvv vvvv is the input which shall be connected to the chosen output.  

 

 

 

vvv vvvv = input number 

 
8.5.3  Video crosspoint set  

Only for use with Video routers. 
Command for setting of crosspoints: 
 
  1010nnnn 0kkkkkkk 0vvvvvvv 
 
 

 

- nnnn is the matrix address from 0 up to 15. 

 

 

- kkk kkkk is the output which shall be controlled.   

 

 

 

kkk kkkk = output number 

   0 

output 

   127 

output 

128 

 
 

 

- vvv vvvv is the input which shall be connected to the chosen output.  

 

 

 

vvv vvvv = input number. 

 

Summary of Contents for TRITON TTN-BVS-1602






















Reviews: