GRAUPNER 32032 Programming Manual Download

Page: 152 / 324

152

Detail program description - Timers (general)

Timers (general)

Timers on the basic display

The default transmitter display shows a total of three
timers. These are: the transmitter operating time on
the left of the display, plus a "Top" and a "Centr" timer
on the right of the display:

#01

0:00h

Stop watch

Flight tim

K78

0:00.0

4.1V

0:00.0

0:00h

Graubele

H-J Sandbrunner

Normal

Runde

RX VOLT:4.9V

Another, ﬂ ight-phase speciﬁ c timer can also be
conﬁ gured with settings in the two menus »

Flight

phase timers

«, page 156, and »

Phase settings

«,

pages 142 and 146. This optional ﬂ ight phase timer –
such as the lap time timer – appears underneath the
"Centr" (ﬂ ight time) timer:

#01

0:00h

Stop watch

Flight tim

K78

0:00.0

4.1V

0:00.0

0:00h

Graubele

H-J Sandbrunner

Normal

Lap

0.0s

RX VOLT:4.9V

To conﬁ gure the "Top" and/or "Centr" timer, use the
selection keys on the left or right touch pad to access
the menu option »

Timers (general)

« in the Multi-

function menu:

Control adjust

Dual Rate / Expo

Channel 1 cur ve

Switch display

Control switch

Logical switch

Phase settings

Phase assignment

Phase trim

Non-delayed chan

Timers (general)

Fl. phase timers

Ser vo adjustment

Stick mode

Control adjust

Dual Rate / Expo

Channel 1 cur ve

Switch display

Control switch

Logical switch

Phase settings

Phase assignment

Non-delayed chan

Timers (general)

Open this menu option with a tap on the center

SET

key of the right touch pad.

Model time

Batt. time

Top :Stop watch

Centr :Flight tim

Timer

–––

12:34h

1:23h

0:00

–––

CLR

" Model time"

This timer shows the currently registered total
access time to the currently active model memory
location. If necessary, this automatic time acquisition
can also be inﬂ uenced by assigning an on/off
switch to this "Model time" timer in the rightmost
column labeled with the switch symbol. This timer
can then be switched on and off as desired. This
switch is assigned (and erased again as required)
as described in the section "Assigning transmitter
controls, switches and control switches" on page 56.
A simultaneous tap on the

keys of the

right touch pad (

CLEAR

) will reset the time back to

"0:00 h".

" Batt. time"

This operating hours timer records the transmitter's
total switch-on time since the last time the battery
was charged, thus monitoring the transmitter battery.
A switch cannot be assigned to this function.

This timer is automatically reset to "0:00 h" when the
transmitter detects that the voltage of the battery is
signiﬁ cantly higher than the last time it was switched
on, e.g. as a result of a charge process or the
installation of a replacement battery.
A simultaneous tap on the

keys of the

right touch pad (

CLEAR

) will also reset this time back

to "0:00 h".

"Top" and "Centr"

These two timers are located at the top right of the
basic display (see the screen image immediately to
the left) and can be assigned a different name; their
function and mode of operation varies according to
the name you give them. Independently of the name
each is given, the "Top" and "Centr" timer can be
programmed to run any length of time forwards or
backwards – see further below.
Use the selection keys of the left or right touch pad to
select the line for the "Top" or "Centr" timer.

Model time

Batt. time

Timer

–––

12:34h

1:23h

0:00

–––

Alarm

Timer

Top :

Stop watch

Centr : Flight tim

Now use the selection keys of the left or right touch
pad to select your desired timer and complete your
selection with another tap on the center

SET

key of

the right touch pad:

"Stop watch"

"Motor

(run)

time"

Both of these two timer variants can be started and
stopped using any of the available switches.
The timer deﬁ ned as "Stopwatch" or "Motor runtime"
sums the "ON" times continually, so that once your
aircraft has landed, you can read off the sum of all
switch "ON" times since the timer was last reset.