GRAUPNER 4831.660, Manual

TIP:  

Of help during programming of the various flight 
phases is the command “Copy flight phase“ in Code 
1

y/erase

meters of 

phase are established and than copi

he

odifie

suit 

2 »

cop

«. First all para

a flight 

ed into t

 next

flight phase where they can be m

d to 

the 

new flying mode. 

“Name“:

 Pres

d use t

tary

se

he list fo

 re

pha

 1 

 reserved 

(ap

mal 

 na

s) 

reate your ow

e 91

 »B

 to 7 is not critical and 

•

 in Code 52 no phase switch is set 

on. 

e 

es are program neutral and serve 

as identification only for the further 
programming of flight phases and hence 
they are displayed in all flight phase 
dependant menus and in the default 
display.  
 

“Fl.ph.tim“:

 Apart from the normal timers in the  

                default display are a number of other  
                timers available. The adjustments for    
                these timers are to be found in Code

62

               »Flight phase timers

«, Page 71 of the

               mc-24/1-hand book. 

Timer selection list: 

s the 

SEL

-key an

he ro

control to cho

 a name from t

r the

quired

ses

to 7. The name “Autorot“ is

on 

for 

the autorotati

phase only.

You can 

art fr

 nor

om using the

n names in Cod

phase

asic 

me

Tim 2 

”Tim2“ stores the “OFF“ and the “ON“ time 

s 

of the relevant switch i.e. the timer restart

d the counter 

with every switch action an
increases by one. 

c

settings«. 
 

The sequence of phases 1
does not have to be continuos. But you begin
always with “phase 1“ the “normal phase“ which is 
always active when

•

 no switch combinations exist 

•

 all phase switches are in default positi

The phase name “normal“ could therefor
be logical for “phase 1“.  
 
The nam

Tim 1, Tim 2, Tim 3, Lap, Tim 1,Tim 2.  
 
While you can record lap times with the 

h 

d 

 
A

ey 

w

d 

k  

 
T
t

ll timers can be halted with the 

STOP

-k

ithout activating the switch which woul

e and the cloc

timer “Lap“, by use of an auxiliary switc
the two new timers after that “Tim1“ an
“Tim2“ have the following meaning: 

increse the counter by on
Tim2 restarts. 

o be able to read the timer memory with 

he rotary controller, you must first stop the 

 
Application: 
Timing of pure flight time if for example a 
control switch on the CH1 controller is 
activated by movement towards max pitch. 
The adjustment for the switching point is 
made in Code 42 »Control switch«. 

“t
 

A

im2“ clock with the

STOP

-key 

pplication

T

over 

fl

iming of normal flight and timing of h

ight. 

 
CLEAR

 – 

display  to th

Notice:

resets the halted timers in the default 

e start value.

with 

transmitte
“Auto tim

With “YE

e 

selected in 

s are 

Tim 1

Recording of time will only occur if in th
line “Lap tim/tim.tab“ a switch is 
Code 62 

»Flight phase timers« 

i.e. an

auxiliary, control or logical switch is in the 
closed position. The number of switch 
activations is indicated in the default 
display. The indication of the counter
contrast inverse as soon as the switch for 
tim1 has been “opened“ (the timer 
stopped): 

STOP

Please note that all timers will be reset 

r switch-ON if you have enabled function 

er reset“ in Code 21 > Base setup model< 

S“. 

NH-90

Mod. 08 

1:18h

U
A

we Corbach

kku 2:34h 

9.8V

FNK

Stoppuhr

Flugzeit

0 00

0 00

RUN

M

0 35

02

 »

:

:

:

Zeit1

«Akro      

OD

Note: 
Als

can the timer be 

halted.  

o with the 

STOP

-key 

new functions 

24 

With the rotary control you can check on
the switch symbols if neseccary.