GRAUPNER 4831.660, Manual

QR

links

WK

links

WK2

links

WK2

rechts

WK

rechts

QR

rechts

 
Functions of the Multi-Flap-Menus: 

QR

: 

In this line you can adjust the amount in 
% by which the camber flaps “FLAP“ and
“FLAP2“ will be working like 

ailerons

when moving the aileron control stick. 

vant 

e changed values 

are reset to default values by pressing 

In the coloumn “AILE“ can the control
deviation for the ailerons also be 
adjusted. The parameter values for all 
three coloumns can here be adjusted 
from  -150% to +150% after the rele
key was pressed. Th

the 

CLEAR

 –key.  

AiI-tr.: 

Here you select  the % amount  by which 
the AILE, FLAP and FLAP2 respond to 
the aileron trim. The control range is from 
-150% to +150% with reference to the 
trim lever . The changed values can be 
reset to the default values by pressing 
the  

CLEAR

 –key. 

Diff.: 

(or “

Aileron differential.

“ If the Multi-

Flap-Menu is not displayed).

In this line you adjust the differential 

24/1-hand book, page 75. 
 
The adjustment range from -100% to 
+100% allows the correct adjustment of 
differential movement independant of the 
direction of servo rotation.The 

CLEAR

 – 

key resets all to default values. 

movement of the control surface for AILE 
and FLAP and FLAP2 (providing the two 
flap pairs are used as ailerons) . For the 
“differential“ explanation refer to the mc-

Note:

r necessary. 

The selection of the / - changes 
the differential direction. The former 
change of servo connections on the 
receiver is no longe

Fl-pos.: 

Here you adjust for all th
AILE,FLAP and FLAP2 the

ree flap pairs  

 flap position 

from –150% to +150%. As the 
adjustments are flight phase dependant – 
you can select for different flap positions 
in the various phases i.e. landing etc. 
 

Note: 
If you - as described immediately  below -
use one or more flight phase dependant 

rollers, than the here adjusted values 

efore 

cont
for the camber flaps are recognised as 
the valid “offset“ or middle positions. A 
flight phase specific offset adjustment in 
Code 32 »Control adjust« is ther
not necessary. 

WK

: 

In this line you enter with the keys 

SYM

or 

ASY

 the characteristic effect for the 

Code 32 »

Control adjust

« accomplished

adjustments of input 6 to the camber flap 
position of the ailerons “AILE“ as wel
camber flap pairs “FLAP and “FLAP2
shall have. 

in 

“ 

a 

n 

l as 

(In the default setting is one of the two 
linear sliders coupled to this input. You 
can instead of the linear slider also use 
switch to change the camber flap positio
within a flight phase - see also example 2 
on page39) 
 
For every pair of flaps a 

sym

metrical or  

asym

metrical action can be selected.

Press the relevant 

SYM

- or 

ASY

-key.  

                 (If the travel

 adjustment inCode 32 

»

Control adjust

« has remained at 

+100%, control values of between 5 and 
20% are normally sufficient. For the 
offset adjustment see note under “

Flap 

pos.

“) 

CLEAR

 resets the changed values back 

to the default of +100% for both pairs of 
camber flaps and 0% for the ailerons.

0% (normal)

WK2

WK

QR

50% (differential)

QR

WK

WK2

new functions

 29

100% (Split)