new functions
32
EL-curve:
This function contains the mixer Brake ->
Elevator.
It means that – if the brake flaps are
deployed as selected in Code 22 »
Mode
type
« with a controller to input 1, 7, 8 or
9 - is normally elevator compensation
necessary.
Change to the next display page with the
arrow key:
l
ts are made as
odel type
« selected
offset will also affect this mixer:
ys at the outmost left side in
directi
sition to
you
mportant notice:
For elevator correction is a 8 point mixer
available. The adjustmen
in the previous software.
See mc-24/1-hand book.
Adjustment for the elevator curve
Brake -> Elevator:
The in Code 22 »
M
The position of the brake controller
indicated by the vertical bar, will only
begin to move away from its end position
in the graphic display when the offset
value is overcome. The remaining brake
travel is automatically expanded to
100%. The neutral point for the elevator
mixer is alwa
the display graphic irrespective of the
selected offset value.
Now you adjust the ELEV - Curve in the
on to the opposite end po
r reqirements:
I
n the transition from “Linear mixer“ to “Curve mixer“
ave the selected values changed.
fter the change to the PROFI-ROM and data
ansfer via cable this was automaticaly taken in
ccount.
By manua
during pro
lue
changed a
out
twice the a
c
case pleas
mixers “Br
in Code 92
Is the diffe
relation of nd-to-end movement on the brake
control stic
usly higher than the selected
value – th
other circu
should be
With that,
known mix
menu“ and
two remain
AILE. >4
2-
RUDD.:
This mixer moves the rudder
with movement of the aileron stick.
The adjustment is symmetrical to the
control stick neutral.
Adjustment range from -150% to+150%.
CLEAR
= 0
The mixer can be switched by nominating
a switch with the key under the right
switch symbol.
The mixer can be switched by nominating
a switch with the key under the right
switch symbol.
I
h
A
tr
a
l programming of a model memory, i.e.
gramming of a new model, has the va
nd must now be programmed with ab
mount as previously used.
Similar changes are valid for manual data transfer
from a m -22 or mc-24 with standard-ROM! In that
e compare the adjustment values of the
ake -> ELEV“ with the relevant indication
»Servo display«.
rence between the two end-values in
e
k obvio
an please use the higher value. For all
mstance the discriptions on page 12
used.
you have found back the previously
er functions of the mc-24 in “multi flap
“Brake adjustments“. Here now are the
ing mixers:
%.
Camb.fl. 6
r
e
etrical to the neutral point of the
controller.
Camb.fl. 6
r
e
etrical to the neutral point of the
controller.
->3 ELEV.:
This mixer applies elevato
compensation by movement of camber
flap controller (normally Control 6). Th
adjustment is symmetrical or
asymm
Adjustment range from -150% to +150%.
->3 ELEV.:
This mixer applies elevato
compensation by movement of camber
flap controller (normally Control 6). Th
adjustment is symmetrical or
asymm
Adjustment range from -150% to +150%.
CLEAR
= 0%.
If you selected a linear slider or switch
(as in Code 32 »
Control adjust
« under
FL on page 29 described) than the
selected controllers will also work in this
mixer. The adjustments have to be made
with sense of direction.
This mixer can also be switched.
Bremse
Kurve
aus
Höhenruder
Eingang
+50
%
Ausgang 0%
Punkt ?
E /A
→
OU
T
P
U
T
-
+
10
0
STO
Höhenruder
Eingang
-10
0
%
Ausgang 0%
Punkt ?
→
OU
-
+
T
P
U
T
10
0
STO
vorn
F L
Multi-Kla
=>
Bremsei stellungen
=>
Querr.
Wölbkl.
Ä C H E N M I S C H E R
ppen-Menü
n
2 >4 Seitenr.
0%
6 >3 Höhenr.
0% 0%
«normal »
SEL
Summary of Contents for 4831.660
Page 41: ...Programming examples 43 ...
Page 42: ...Personal notes 44 ...
