GRAUPNER 4831.660, Manual

Place switch toggle in centre position. 

1. 

Programming examples

 41

2. Press the 

-key and move the switch

toggle to one end position.

3. Return switch toggle to centre position. 

4. Press the left 

-key and move switch 

toggle to other end position. 

Eing.  5     frei

0%  +100%+100%  0.0  0.0

Eing.  6  10    9

0%  +100%+100%  2.0  2.0

Eing.  7     frei

0%  +100%+100%  0.0  0.0

Eing.  8     frei

0%  +100%+100%  0.0  0.0

                            Offset     -  Weg  +        -Zeit+ 

«Thermik»  

ASY

SYM

SEL

ASY

SYM

 for the two end 

pend 

ced 

The position of the flaps and ailerons
positions and centre position of the switch de
on the value set in “- “. It is also influen
by the offset and the mixing value in the Multi – Flap 
- Menu (Code 71) , see further down. We leave the 
control travel at +100% symmetrical and the offset at 
0% as shown in the display page above.  
 

It is advisable to select in column “-time+“ a 
symmetrical or asymmetrical delay time between the 
three switch positions for a “soft“ switch transition, 
in our example “2.0 s / 2.0 s“. 
 
Now back the Multi–Flap–Menu of ... 

Code 71 »Wing mixer« 

  QR 

+80% 

 +60% 

+100%   

+50% 

QR-Tr. 
Diff. +50% 

+30%

WK-Pos +10%   

+15% 

  WK 

+10%  +10%  +15% +15% 

HR  >WK  +10%  +10%  +15% +15% 
«Thermik»

     QR                 WK                 

ASY

SYM

ASY

SYM

Now you change in the flight phase “Thermal“ the 
values for “Fl-pos.“ And “Fl“: 

Fl-pos.: 

Here you position for the phase 
“Thermal“ the ailerons and flaps for t
flight neutral position of the slider or 
switch (centre). 

FL:

he in 

In this line you program the amount by 
which the ailerons and  flaps will move a
camber flaps by use of the linear slider o
toggle position of the switch. (Due to no
linear lift distribution the mixing value for
the flaps should be a little higher than for 
the ailerons.) 

s 

r 

n 

C

v

LEAR

 is the reset command to return the changed 

alues to the default settings. 

or you can 

eron and 

Move the CH 1 control stick to the full foreward 

position so that you may identify the position of the 

adjustment of +10% for the Ail and +15% for the Fl 

To adjust the elevator, return to the basic page of 

 
After a short push on the rotary select
check on the camber flap positions for ail
flap in the »

Servo display

« in relation to the linear 

slider on input 6 or the 3–pos–switch.  
 
 

(

camber settings better while using the linear slider 
or 3-pos-switch.): 

•

 In the controller centre position only the “Fl-pos“-

is effective.  

•

 On one end position of the controller are the Ail 

and Fl in neutral again as the here pre selected 
mixer value for the Fl-pos adjustment compensates 
and 

•

 in the other end position the aileron and flap servos 

run to the  the lower maximum position. 

the »

Wing mixer

«-menu: 

        F  L  Ä  C  H  E  N  M  I  S  C  H  E  R

en-Menü  

 =>
 

ölbkl. 

6  >3  Höhenr. 

     +5%    +5%

Multi-Klapp
Bremseinstellungen  =>
Querr. 

2  >4  Seitenr. 

    0%

W

«Thermik»

SEL ASY

In both end positions of the 3 position switch is the 
elevator re adjusted by symmetrical 5% in our 
example (note the correct direction). 
With the linear slider the elevator is proportionally 

ontrolled in the correct direction. 

 compensate for further flap 

oment or attitude of the model, you change to ...  

c
 
 
 

f the elevator has to

I
m