background image

INNOVATION & TECHNOLOGY 

REV 1 

WARNING 

Always  disconnect  ALL  of  the  propellers  when  setting  up  your  radio  or 
receivers to avoid serious injury by turning propellers! 

Check the receiver regularly for damages to the housings and cables after 
every  flight.  Damaged  or  wet  electronic  components,  even  if  re-dried, 
should no longer be used. 

PRODUCT FEATURES 

The Alpha 250Q racer comes in two different versions. 

FEATURES 

RFH 

RTF 

Fully assembled Alpha 250Q 

Yes 

Yes 

Aluminum Carrying Case  

Yes 

Yes 

Graupner C-Props (2 sets) 

Yes 

Yes 

mz-12 6ch telemetry radio 

 

Yes 

LiPo battery charger 

 

Yes 

3S 1500 mAh LiPo battery 

 

Yes 

AC Power cable 

 

Yes 

ALPHA 250Q SPECIFICATIONS 

 

Expertly built no assembly needed 

 

Integrated triple mode receiver and flight controller 

 

Selectable flight modes (beginner to expert) 

 

Receiver  with  out-of-the-box  built  in  telemetry  (altitude, 
voltage, RF signal strength, Rx temperature) 

 

Live voice telemetry announcements of flight data 

 

Warning  voice  notifications  of  battery  level,  radio  range  and 
assigned maximum altitude 

 

Over the air access for copter setup with any Graupner HoTT 
radio (6ch and up) 

 

No computer or setup boxes needed to configure or operate 

 

Powerful,  lightning  fast  response  Graupner  Ultra  2300Kv 
motors 

 

Graupner high performance copter C-Props 

 

 

 

Strong 3mm carbon motor frames and 2mm carbon chassis  

 

Heavy  duty  aluminium  carrying  case  for  radio,  copter  and 
equipment transport 

 

Carbon vibration free camera mount 

Summary of Contents for Hott Alpha 250Q






















Reviews: