Warnings
In the display of the
mz-24
HoTT Pro transmitter ap-
pear different warning windows. These can be divided
into two groups:
"Warning" display
These warning windows primarily appear after the
transmitter is turned on and indicate certain operating
states. In the following illustration, for instance, the
red dot after "CH1-POS" indicates that the throttle
servo connected to the output 1 in fixed-wing models,
or the throttle servo and to output 6 on an helicopter
model, is not in the idle position and there is the risk
of a runaway engine. Until this state persists, the con-
tent of the underneath field are obscured for safety
reasons ...
... until the Throttle/Pitch control stick is not in the idle
area:
Basically the it is the same for the warning option "Thr.
HOLD", with the difference that the sub-men "
WARN-
ING
" of the system menu it can be selected, depend-
ing on the model, if the motor stop function on/off
must be worn:
Notice
In no case you should use the possibility of the
servo reverse of the channel 6 for helicopters and
channel 1 for other model types to reverse the
direction in which the related control stick works. Be-
cause the switch-on warning "
CH1-Pos
" as the "
Thr.
HOLD
" function do not follow this kind of reverse control
direction. To reverse the control direction use exclusively
the possibility offered by the "
Pitch curve
" menu for
helicopters models and "
Throttle curve
" for all the oth-
er model types.
Touch
SET
with a finger or the provided stylus to go
directly to the
»TX ctl«
display (Transmitter setting) in
which you can link the receiver to the model memory
as described in the related paragraph ...
Or touch the
BACK
button at the top left to terminate
the procedure.
If instead by switching the transmitter, there is already
a receiver bound to the model memory and
inactive
Thr.POS warning, the transmitter will switch on and
the RF module will also be active. Otherwise in the
middle of the display it will standardly appear the fol-
lowing page and at the same time an acoustic warn-
ing will be emitted.
You now have the option of waiting a few seconds
until the display disappears automatically or maintain-
ing the HF transmissions by manually tapping the
ON
button, or switching them off by tapping the
OFF
button.
In the field between the two green lines, the message
"RC signal" indicates that the transmitter is set to nor-
mal remote control. Alternately, messages such as
"TEACH signal" or "PUPIL signal" can appear here.
Another – possible – variant is to display "SET F/S" as
an indication that no fail-safe settings have yet been
made.
Notices
• By default, only the monitoring of the "
Warn-
ing
" sub-menu is activated in the display of
the sub-menu "Warning" of the system menu.
• By selecting
REV
in the "Thr.HOLD" line of
the "
Warning
" sub-menu the transmitter can
remind you to switch this function safely on.
8
Warnings
Summary of Contents for mz-24 PRO
