34 / 48
S1024.mz32_V1.7_sh_en
Telemetry
The telemetry c
ŽŶŶĞĐƟŽŶ
between the transmi
Ʃ
er and receiver
takes place via the return channel of the HoTT receiver de
ĮŶĞĚ
as
the main receiver. If more than one receiver is bound to a model
memory, the return channel will be by default the last bound receiver.
This assignment can be changed in the submenu “RF Set” in the base
menu or at the special “Telemetry” menu.
Depending on the se
ƫŶŐ
of the value
ĮĞůĚ
at the “Tele. Cycle” the
transmission of telemetry data takes place a
Ō
er each fourth data
packet. This also in
ŇƵĞŶĐĞƐ
the r
ĞĂĐƟŽŶ
ƟŵĞ
to control inputs when
making se
ƫŶŐ
changes at the ASCII menu when se
ƫŶŐ
up for exam-
ple a
ŇŝŐ
ht controller using the wireless interface. The corresponding
delay does not cons
ƟƚƵ
te an error
Note
Sensors must always be connected to the main receiver, since only
the return channel of this receiver is evaluated by the transmi
Ʃ
er.
A
Ʃ
en
ƟŽŶ
Programming on the model or on sensors must not be carried out
during ongoing model opera
ƟŽŶ
and only when the engine/motor
is switched o
ī͊
Select Rx
Up to four receivers can be bound to a model memory in the sub-
menu “RF Set” of the basic menu. However, a telemetry c
ŽŶŶĞĐƟŽŶ
can only ever be established to one of these four receivers which as
standard is always the last bound receiver. All sensors are to be con-
nected to the receiver that is designated as the receiver from which
we expect to receive telemetry informa
ƟŽŶ
from. This is important
in a
ŵƵůƟ
receiver con
ĮŐƵ
ra
ƟŽŶ
and therefore will require proper
planning as to the loca
ƟŽŶ
of the receiver which should be close to
where the telemetry sensors are installed.
In the “RF Set” menu the receiver that has the “T.Sel”
ĮĞůĚ
checked
is the receiver that provides telemetric informa
ƟŽŶ
to the transmit-
ter
Viewing telemetric informa
ƟŽŶ
or se
ƫŶŐƐ
from
ĂĚĚŝƟŽŶĂů
receivers
bound to the model can be done by tapping on the “RX Select”
ĮĞůĚ
which will show an lis
ƚǁŝƚŚĂůůĂĐƟ
ve receivers to pick from.
A
Ʃ
en
ƟŽŶ
This also changes the assignment in the column
"T. sel." of the submenu "RF Set". A
Ō
er comple
ƟŶŐ
the adjustments,
it may be necessary to restore the original assignment!
Summary of Contents for mz-32 HoTT
