background image

GB - 14

Throttle-Diesel Models

The throttle knob controls the engine speed.

To increase engine speed: 

Turn throttle knob to unlocked position.

Pull the throttle knob out slowly until desired 
engine speed is reached.

Turn the knob either to left or right to lock in 
position.

To decrease engine speed:

Turn throttle knob to unlocked position.

Push the throttle knob in slowly until desired 
engine speed is reached.

Turn the knob either to left or right to lock in 
position.

Warning Lights-Diesel Models

Oil Pressure Warning Light

If this light comes on, there has been a 
loss of engine oil pressure.

IMPORTANT: 

When the oil pressure light comes on, 

stop the unit and engine as quickly as possible. Service 
or repair unit before restart.

NOTE: 

The oil pressure light comes on when the key is 

turned to RUN or beyond. It should go off once the 
engine starts.

Temperature Warning Light

If the coolant temperature reaches or 
exceeds a boiling condition the temperature 
warning light comes on. If this light comes 
on, take the following actions:

1. Stop the unit operation in a safe place and run the 

engine at idle, without a load.

2. Do not stop the engine. Allow it to idle for 5 

minutes.

3. If the engine stalls within that 5 minutes, 

immediately leave and stay away from the 
machine.

4. Keep away from the unit for at least 10 minutes to 

allow the engine pressure to drop. 

5. After engine has cooled, check coolant level and 

that fan belt is intact.

Hour Meter - Diesel Models

The hour meter records engine operation time. It 
operates when the ignition switch is in the RUN 
position.

NOTE: 

For accurate readings, be sure ignition switch is 

OFF when unit is not operating.

Traction Control Levers

The traction control levers control the unit’s speed and 
direction. Always move levers slowly and smoothly. 
Refer to

 Driving the Unit

 for operating instructions.

Attachment Tilt  Lever

To tilt attachment forward, slowly 
push the attachment tilt lever 
forward.

To tilt attachment rearward, slowly 
pull the attachment tilt lever 
rearward.

Lift Arm Control

Move the lift arm lever forward to lower the 
lift arms. 

Move the lift arm lever toward the rear of 
the unit to raise the lift arms.

07755500A

OK0421

FAST

SLOW

LOCKED

LOCKED

UNLOCKED

OK0560

OK0280

CAUTION: 

STRIKING OBJECTS may 

damage unit and result in minor or moderate 
injury. Shut off unit and engine. Check for any 
damage or loose parts. Repair if necessary 
before restart.

WARNING: 

AVOID BODILY INJURY. Always 

return lift arms to down position before getting 
off unit or stopping engine.

OK0440

OK0460

Summary of Contents for Skidster 200



































Reviews: