GREAT PLANES Avistar 30cc ARF, Instruction Manual

36

model will be able to reach the landing zone (on dead-stick 
landings it is common to land with no fl aps at all). Without 
engine power, fl aps can unexpectedly reduce the model’s 
range, thus causing you to come up short of the fi eld.

Have a goal or fl ight plan in mind each time you fl y. This may 
be learning or improving a maneuver or learning how the 
model behaves at certain speeds and control rates. Every 

maneuver should be deliberate, not impulsive. A fl ight plan 
reduces the chances of crashing your model because of 
poor planning and impulsive moves.

Have a ball! But always stay in 

control and fl y in a safe manner.

GOOD LUCK AND GREAT FLYING! 

  QTY.                            DESCRIPTION                                     QTY.                            DESCRIPTION

PARTS LIST

  1  Fuel Tank stopper
  1  Fuel tank stopper screw
  1  Fuel tank stopper plate large
  1  Fuel tank stopper plate small
 2 clunks
  1  Long brass tube
  2  Short brass tube
  8  small nylon tie straps
 1 Spinner 

backplate

 1 Spinner 

bolt

  1  Spinner backplate adapter
 1 Plastic 

fl oor

  3  16.5" outer pushrod tube
  2  Hook and loop material 300mm
  1  Tail gear bracket
  1  Tail gear spacer
  1  Tail gear spacer set screw
  1  Tail gear bushing
  1  Tail gear wire support
  1  Tail gear wheel collar
  1  Tail gear wheel collar set screw
  7  Extra large control horns
  3  Control horn back plates
  3  Plywood engine mount spacers
  2  10 x 30mm Wing dowels
  1  8 x 30mm wing alignment dowel
  4  Plywood motor mount top and bottom
  4  Plywood motor mount sides
  4  Plywood motor mount ends w/tabs
  2  Plywood motor mount ends no tabs
  1  Plywood outer pushrod tube support long
  1  Plywood outer pushrod tube support short
  1  Fuselage weight cover
  7  4-40 Solder clevis
  4  4-40 x 6" metal pushrod

  7  4-40 metal clevis
  23  #4 x 1/2" sheet metal screw
 7 4-40 

nut

  16  silicone clevis keeper
 2 3/16" 

axle

  2  3/16" axle nut
  4  3/16" Wheel collar
  4  6-32 x 1/4" socket head cap screw
  4  4-40 x 1/2" machine screw
 11  #4 

fl at washer

  4  #4 lock washer
  8  6-32 x 3/4" socket head cap screw
 8 #6 

fl at washer

  8  #6 lock washer
  8  8-32 Blind nuts
  4  8-32 x 3/4" socket head cap screw
  4  8-32 x 1" socket head cap screw
 8 #8 

fl at washer

  8  #8 Lock washer
  12  4-40 x 1" socket head cap screw
  3  4-40 x 48" threaded rod
  1  2-56 x 36" theaded pushrod
  2  1/4-20 x 2" nylon wing bolt
  1  aluminum fuel plug
  11  #2 x 3/8" sheet metal screw
 11  #2 

fl at washers

  1  Brass screw lock connector
  1  screw lock retainer
  1  4-40 x 1/4" socket head cap screw
  1  white inner pushrod tube
  4  2-56 x 1" threaded stud
  2  2-56 pivot balls
 2 2-56 

nut

  2  Nylon pivot ball sockets
 2 nylon 

clevis