background image

5

Kit Contents

1. Fuselage
2. Propeller
3. Motor & Gear Drive
4. Hardware Bag
5. Horizontal Stab (L&R)
6. Rudder
7. Fin
8. Left Wing Half
9. Left Aileron
10. Right Wing Half
11. Right Aileron

Kit Contents (not photographed)

(3) Control Horns 
(3) Control Horn Retainers
(2) Stabilator Spacer/Control Horns
(2) Nylon Pin Hinges 
(4) Micro FasLinks 
(5) Propeller Rubber Bands 
(1) Double-sided Control Horn Extension 
(2) Single-sided Control Horn Extension
(1) Hook and Loop Fastener

(1) Elevator Pushrod
(1) Rudder Pushrod 
(2) Aileron Pushrods
(1) Prop Saver
(1) Tape 

Before starting to build, take an inventory of this kit to make sure it is complete, and inspect the parts to make sure they are of
acceptable quality. If any parts are missing or are not of acceptable quality, or if you need assistance with assembly, contact Product
Support
. When reporting defective or missing parts, use the part names exactly as they are written in the Kit Contents list.

Great Planes Product Support:

3002 N Apollo Drive, Suite 1

Champaign, IL 61822

Telephone: (217) 398-8970, ext. 5

Fax: (217) 398-7721

E-mail:

airsupport@greatplanes.com

KIT CONTENTS

1

2

5

7

8

6

10

9

11

To convert inches to millimeters, multiply inches by 25.4

3

4

Summary of Contents for EP YAK 55 3D

















Reviews: