background image

Low Rate

Template

High Rate

Template

Control Throw Templates

Other Items Available from Great Planes & Hobbico

ElectriFly

BL-8 Brushless Electronic 

Speed Control (GPMM2070)

ElectriFly’s BL-8 is a fully proportional forward/reverse
ESC with brake. Compatible with NiCd, NiMH, and Li-Po
batteries, it has custom BEC that handles up to
1.5A–perfect for models that use up to three high-powered
servos. Programmable features include brake control, safe
start, and switching frequency.

Hobbico

®

Pro Series

Quick

Field Charger MkII (HCAP0290)

The MkII is two completely independent chargers in a single
case! Current on both sides adjusts from 0.2-2A, to fast charge
1-3 cell Li-Ion or Li-Po park flyer batteries or peak charge 1-8
cell NiCd or NiMH radio packs. Auto-trickle for NiCds and NiMH
packs is automatically set, based on the fast-charge rate. Hook
up the pack, press the start button – and twin LEDs signal the
cell type and charge method to be used by color: red for NiCd,
yellow for NiMH and green for Li-Ion or Li-Po cells. Jacks make
it easy to hook up your pack – and a voltmeter – to either side.

ElectriFly

RimFire

22M-1000 Brushless Motor

(GPMG4500)

Perfect for small, high performance planes such as FlatOuts and smaller 3D aerobats,
the RimFire has an exceptionally high power-to-weight ratio and an efficiency rating
of 77%! Its “outrunner” design eliminates the need for an external gear drive, for
easier installation and less weight. Simply attach the prop to the motor with a rubber
band (no prop adapter required)…the prop will simply “pop” off in a crash.

Summary of Contents for Extra 300S ARF

























Reviews: