background image

19

This model belongs to:

Name

Address

City

, State

, Zip

Phone Number

AMA Number

and the model is a foot or so off the deck, smoothly increase 
up elevator until it gently touches down. Once the model is 
on the runway and has lost fl ying speed, hold up elevator to 
place the tail on the ground, regaining tail wheel control. Try 
to land slowly and gently.

One fi nal note about fl ying your model. Have a goal or fl ight 
plan in mind for 

every 

fl ight. This can be learning a new 

maneuver(s), improving a maneuver(s) you already know, 
or learning how the model behaves in certain conditions 

(such as on high or low rates). This is not necessarily to 

improve your skills (

though it is never a bad idea!)

, but more 

importantly so you do not surprise yourself by impulsively 
attempting a maneuver and suddenly fi nding that you’ve run 

out of time, altitude or airspeed. Every maneuver should be 
deliberate, not impulsive. For example, if you’re going to do a 
loop, check your altitude, mind the wind direction (anticipating 
rudder corrections that will be required to maintain heading), 
remember to throttle back at the top, and make certain you 
are on the desired rates (high/low rates). A fl ight plan greatly 
reduces the chances of crashing your model just because 
of poor planning and impulsive moves. 

Remember to think.

Have a ball! But always stay in control 

and fl y in a safe manner.

GOOD LUCK AND GREAT FLYING!

Summary of Contents for FACTOR 3D





















Reviews: