background image

5

To order replacement parts for the Great Planes Headwind B, use the order numbers in the Replacement Parts List that
follows. Replacement parts are available only as listed. Not all parts are available separately (an aileron cannot be
purchased separately, but is only available with the wing kit). Replacement parts are not available from Product Support,
but can be purchased from hobby shops or mail order/Internet order firms. Hardware items (screws, nuts, bolts) are also
available from these outlets. If you need assistance locating a dealer to purchase parts, visit www.greatplanes.com and
click on “Where to Buy.” If this kit is missing parts, contact Great Planes Product Support.

Replacement Parts List

Order Number

Description

How to Purchase

Missing pieces ................................................Contact Product Support
Instruction manual...........................................Contact Product Support
Full-size plans .................................................Not available
Kit parts listed below.......................................Hobby Supplier

GPMA2570 ...........Fuselage Set
GPMA2572 ...........Wing Set
GPMA2574 ...........Tail Set
GPMA2576 ...........Landing Gear Set
GPMA2578 ...........Windshield
GPMA2580 ...........Hardware Pack

ORDERING REPLACEMENT PARTS

5

1

2

3

4

10

9

7

8

6

1

Fuselage (w/windshield 
and outer pushrods)

2

Horizontal tail

3

Vertical tail

4

Left wing

5

Right wing

6

Wing joiner

7

GP motor mount

8

GWS motor mount

9

Main gear wire

10

Main wheels

(2) Control horns
(2) Clevises
(4) Wheel retainers
(1) Tail skid wire
(1) Balsa main gear block
(1) Plastic wing TE support
(1) Bag small rubber bands (battery)
(1) Bag large rubber bands (wing)
(2) Pushrod wires

Kit Contents (Photographed)

Kit Contents (Not Photographed)

Before starting to build, use the Kit Contents list to take an inventory of this kit to make sure it is complete and inspect
the parts to make sure they are of acceptable quality. If any parts are missing or are not of acceptable quality, or if you
need assistance with assembly, contact Great Planes Product Support. When reporting defective or missing parts, use
the part names exactly as they are written in the Kit Contents list on this page.

3002 N. Apollo Drive, Suite 1

Champaign, IL 61822

Telephone: (217) 398-8970

Fax: (217) 398-7721

E-mail: airsupport@greatplanes.com

KIT INSPECTION

Summary of Contents for HeadWind "B"

















Reviews: