background image

WARRANTY

Great Planes

®

Model Manufacturing Co. guarantees this kit to be free from defects in both material and workmanship at the date of purchase. This warranty

does not cover any component parts damaged by use or modification. In no case shall Great Planes’ liability exceed the original cost of the purchased kit.
Further, Great Planes reserves the right to change or modify this warranty without notice.

In that Great Planes has no control over the final assembly or material used for final assembly, no liability shall be assumed nor accepted for any damage resulting
from the use by the user of the final user-assembled product. By the act of using the user-assembled product, the user accepts all resulting liability.

If the buyer is not prepared to accept the liability associated with the use of this product, the buyer is advised to return this kit immediately in new and
unused condition to the place of purchase.

To make a warranty claim send the defective part or item to Hobby Services at the address below:

Hobby Services

3002 N. Apollo Dr. Suite 1

Champaign IL 61822

USA

Include a letter stating your name, return shipping address, as much contact information as possible (daytime telephone number, fax number, e-mail address), a
detailed description of the problem and a photocopy of the purchase receipt. Upon receipt of the package the problem will be evaluated as quickly as possible.

READ THROUGH THIS MANUAL BEFORE STARTING
CONSTRUCTION. IT CONTAINS IMPORTANT INSTRUCTIONS
AND WARNINGS CONCERNING THE ASSEMBLY AND
USE OF THIS MODEL.

GPMZ0252 for GPMA1153  V1.0

Entire Contents © Copyright 2004

Champaign, IL

(217) 398-8970, Ext. 5

airsupport@greatplanes.com

INSTRUCTION MANUAL

Wingspan: 41 in [1040mm] 
Wing Area: 269 sq in [17.4 dm

2

Weight: 10 oz [285g]
Wing Loading: 7.5 oz/sq ft [23 g/dm

2

Length: 29.5 in [750mm] 
Radio: 3-channel with 2 sub-micro servos
Motor: T-280-size with 3.5:1 gear box
Motor Battery: 9.6V – 650 mAh 

Summary of Contents for J-3 Electri Cub





















Reviews: