1. Your Lancair ES EP ARF should not be considered a toy,
but rather a sophisticated, working model that functions very
much like a full-size airplane. Because of its performance
capabilities, the Lancair, if not assembled and operated
correctly, could possibly cause injury to yourself or
spectators and damage to property.
2. You must assemble the model according to the
instructions. Do not alter or modify the model, as doing so
may result in an unsafe or unflyable model. In a few cases
the instructions may differ slightly from the photos. In those
instances the written instructions should be considered
as correct.
3. You must take time to build straight, true and strong.
4. You must use an R/C radio system that is in first-class
condition and correctly sized components (servos, wheels,
etc.) throughout the building process.
5. You must correctly install all R/C and other components so
that the model operates correctly on the ground and in the air.
6. You must check the operation of the model before every
flight to insure that all equipment is operating and that the
model has remained structurally sound. Be sure to check
clevises or other connectors often and replace them if they
show any signs of wear or fatigue.
7. If you are not an experienced pilot or have not flown this
type of model before, we recommend that you get the
assistance of an experienced pilot in your R/C club for your
first flights. If you’re not a member of a club, your local hobby
shop has information about clubs in your area whose
membership includes experienced pilots.
8. WARNING: The fuselage, cowl, wheel pants and wing tips
included in this kit are made of fiberglass, the fibers of which
may cause eye, skin and respiratory tract irritation. Never
blow into a part (wheel pant, cowl) to remove fiberglass dust,
as the dust will blow back into your eyes. Always wear safety
goggles, a particle mask and rubber gloves when grinding,
drilling and sanding fiberglass parts. Vacuum the parts and
the work area thoroughly after working with fiberglass parts.
Remember: Take your time and follow the instructions to
end up with a well-built model that is straight and true.
A 4-channel radio system with a micro receiver and four
micro servos are the minimum requirements for the Lancair
EP ES ARF. The radio components can be purchased as
separate items or can be purchased as a package system.
If you already have a Futaba
®
or Futaba-compatible
transmitter you plan to use with this model, part numbers for
the servos and receiver are provided below:
❏
(4) Futaba S3103 Servo Micro Mini (FUTM0037)
❏
Futaba R114F 4-channel FM micro receiver w/o crystal
(low band – FUTL0442, high band – FUTL0443)
❏
Futaba FM single conversion receiver crystal for R114F
(low band – FUTL62**, high band – FUTL63**)
If you plan to purchase a complete radio system, the Futaba
4YF micro system is packaged with the Futaba R114F and two
S3108 micro servos. You will need to purchase an additional
two micro servos. The order numbers are provided.
❏
Futaba 4YF 4-Channel Micro FM/2 S3108 Servos (FUTJ37**)
❏
(2) Futaba S3108 Servo Micro 7.6 g (FUTM0042)
Since the Lancair ES EP ARF uses dual aileron servos, a
Y-harness will be required to connect the servos together as
well as one 9" [230 mm] servo extension. The order numbers
are provided below:
❏
Futaba 6" Dual Servo Extension J (FUTM4130)
❏
Futaba 9" Servo Extension J (FUTM3910)
The included battery is a 9.6V 1800mAh NiMH pack. A NiMH
compatible charger is required. An economical choice is the
Great Planes ElectriFly
™
400 DC charger. A Deans male ultra
plug will also be necessary (soldering is required):
❏
Great Planes ElectriFly Peak 400 DC 1-10C Peak
Charger (GPMM3001)
❏
Deans 2-Pin Ultra Plug (WSDM3001)
For a more advanced computerized charger, we recommend
the Great Planes Triton
™
charger. Charge leads are not
included with this model charger, so order numbers for the
correct connector type, wire leads, and banana plugs are
listed below (soldering is required):
❏
Great Planes ElectriFly Triton
™
DC Competition Peak
Charger (GPMM3150)
❏
Deans Male Ultra Pigtail (WSDM2013)
❏
Hobbico
®
Banana Plugs (6) (HCAP0310)
Charger
Radio Equipment
DECISIONS YOU MUST MAKE
We, as the kit manufacturer, provide you with a top quality,
thoroughly tested kit and instructions, but ultimately the
quality and flyability of your finished model depends on
how you build it; therefore, we cannot in any way
guarantee the performance of your completed model, and
no representations are expressed or implied as to the
performance or safety of your completed model.
PROTECT YOUR MODEL, YOURSELF
& OTHERS...FOLLOW THESE
IMPORTANT SAFETY PRECAUTIONS
3
