background image

Introduction ......................................................................2
Precautions .......................................................................2
Radio System Requirements...........................................3
Engine Selection ..............................................................3
Additional Items Required...............................................4

Hardware and Accessories ..........................................4
Adhesives and Building Supplies ................................4
Optional Supplies and Tools ........................................4
General Inspection.......................................................4

Important Building Notes ................................................4

Parts List ......................................................................5
Metric / Inch Scale .......................................................5

Build the Wing ..................................................................6

Join the Wing Halves ...................................................6
Hinge the Ailerons........................................................7
Hook up the Ailerons ...................................................7
Mount the Landing Gear ..............................................8

Join the Control Surfaces to the Fuse ...........................9

Install the Stab .............................................................9
Install the Fin .............................................................10

Hook up the Controls.....................................................11

Connect the Pushrods ...............................................11
Mount the Tail Gear ...................................................13
Join the Tail Fairings ..................................................14
Mount the Engine.......................................................15
Mount the Cowl..........................................................16
Finish Radio Installation.............................................17

Final Scale Details..........................................................18

Mount the Wing Struts ...............................................18
Finish the Cockpit ......................................................18

Get the Model Ready to Fly...........................................19

Check the Control Directions .....................................19
Set the Control Throws ..............................................19
Balance the Model .....................................................20
Balance the Model Laterally ......................................20

Preflight ...........................................................................21

Identify Your Model ....................................................21
Charge the Batteries..................................................21
Balance Propellers.....................................................21
Ground Check............................................................21
Range Check .............................................................21

Engine Safety Precautions ............................................21
AMA Safety Code (Excerpt)...........................................22

General ......................................................................22
Radio Control .............................................................22

IMAA Safety Code (Excerpt)..........................................22
Check List .......................................................................24
Flying ...............................................................................24

Fuel Mixture Adjustment ............................................25
Takeoff .......................................................................25
Flight ..........................................................................25
Landing ......................................................................25

Engine Mount Template .................................................27

Thank you for purchasing the Great Planes Ryan STA ARF.
When we assembled the first Ryan prototype in our R & D shop,
we could tell right away that this was going to be a popular
model. Its classic outline and friendly-looking proportions, not to
mention the striking black-and-white checkers with red trim,
cannot be resisted by veterans and new modelers alike.
Experienced builders will appreciate the quality glasswork and
paint job on the cowl and wheel pants, knowing that it takes
hours in the shop to duplicate the same result.

When it's time to fly your Great Planes Ryan STA ARF, rest
assured. Its flight performance more than lives up to its
great looks. This model is definitely one of the most gentle,
honest, enjoyable ARFs around! Even in mild crosswinds,
you'll find yourself putting on a show while others watch as
you shoot touch-and-goes and smooth landings (on
pavement or grass!).

Enough talk. Let's start building so you can see for yourself...

While the Great Planes Ryan ARF is easy to build and flies
well, it is not intended to be a beginner's model. It lacks the
self-recovery characteristics of a good basic trainer such as
a Great Planes PT

model. However, if you have learned

the basics of R/C flying, the Ryan STA ARF is an excellent
choice to try your skills at flying a large-scale model.

Your Ryan STA ARF is not a toy, but rather a sophisticated,
working model that functions very much like a full-size
airplane. Because of its realistic performance, the Ryan STA
ARF, if not assembled and operated correctly, could possibly
cause injury to yourself or spectators and damage property.

To make your R/C modeling experience totally enjoyable, if
this is your first “giant” R/C model, we recommend that you
get the assistance of a pilot who has experience with this
type of plane for your first flights. If you're not currently a
member of an R/C club, your local hobby shop has
information about clubs in your area whose membership
includes experienced pilots.

If you're not currently an AMA (Academy of Model
Aeronautics) member, we strongly urge you to join. There are
over 2,500 AMA chartered clubs across the country. Among
other benefits, the AMA provides insurance to its members
who fly at sanctioned sites and events. Additionally, training
programs and instructors are available at AMA club sites to
help you get started the right way. Contact the AMA at the
following address or toll-free phone number:

PROTECT YOUR MODEL, YOURSELF

& OTHERS...FOLLOW THIS

IMPORTANT SAFETY PRECAUTION

INTRODUCTION

TABLE OF CONTENTS

2

Summary of Contents for Ryan STA





























Reviews: