background image

INSTRUCTION MANUAL

Wingspan: 39.5 in [1005mm]
Wing Area: 234 in

2

 [15.1dm

2

]

Weight: 24 – 26 oz [680 – 735g]
Wing Loading: 14.8 – 16 oz/ft

2

 [45 – 49g/dm

2

]

Length: 33.5 in [845mm]
Radio:   4-channel, three servos
Electric Motor: 1.1 in [28mm] dia., 110 W, 25A ESC

WARRANTY

Great Planes

®

 Model Manufacturing Co. guarantees this kit to be free from defects in both material and workmanship at the date of purchase. 

This warranty does not cover any component parts damaged by use or modifi cation. In no case shall Great Planes’ liability exceed the 
original cost of the purchased kit.
 Further, Great Planes reserves the right to change or modify this warranty without notice.

In that Great Planes has no control over the fi nal assembly or material used for fi nal assembly, no liability shall be assumed nor accepted 
for any damage resulting from the use by the user of the fi nal user-assembled product. By the act of using the user-assembled product, 
the user accepts all resulting liability.

If the buyer is not prepared to accept the liability associated with the use of this product, the buyer is advised to return this kit 
immediately in new and unused condition to the place of purchase.

To make a warranty claim send the defective part or item to Hobby Services at the address below:

Hobby Services

3002 N. Apollo Dr., Suite 1

Champaign, IL 61822 USA

Include a letter stating your name, return shipping address, as much contact information as possible (daytime telephone number, fax 
number, e-mail address), a detailed description of the problem and a photocopy of the purchase receipt. Upon receipt of the package 
the problem will be evaluated as quickly as possible.

READ THROUGH THIS  MANUAL  BEFORE 
STARTING CONSTRUCTION. IT CONTAINS 
IMPORTANT INSTRUCTIONS AND WARNINGS 
CONCERNING THE ASSEMBLY AND USE OF 
THIS MODEL.

Champaign, Illinois

(217) 398-8970, Ext 5

airsupport@greatplanes.com

Entire Contents © Copyright 2007

GPMZ1169 for GPMA1169  V1.0

Summary of Contents for Seawind EP





















Reviews: