background image

4

Before starting to build, use the Kit Contents list to take an inventory of this kit to make sure it is complete, and inspect
parts to make sure they are of acceptable quality. If any parts are missing or are not of acceptable quality, or if you need
assistance with assembly, contact Great Planes Product Support. When reporting defective or missing parts, use the
part names exactly as they are written in the Kit Contents list on this page.

Great Planes Product Support

Telephone: (217) 398-8970

Fax: (217) 398-7721

E-mail: productsupport@greatplanes.com

You can also check our web site at www.greatplanes.com for the latest Slinger updates.

KIT CONTENTS

ORDERING REPLACEMENT PARTS

To order replacement parts for the Great Planes Slinger ARF, use the order numbers shown below. Replacement parts are
available only as listed. Not all parts are available separately. Replacement parts are not available from Product Support,
but can be purchased from hobby shops or mail order/Internet order firms. Hardware items (screws, nuts, bolts) are also
available from these outlets. If you need assistance locating a dealer to purchase parts, visit  and click on “Where to Buy”.
If this kit is missing parts, contact Great Planes Product Support.

Part # 

Description

How to Purchase

GPMA2423 ......W

ING SET

....................Contact Your Hobby Dealer

GPMA2424 ......Center wing cover ......Contact Your Hobby Dealer
GPMA2425 ......W

ING TIPS

....................Contact Your Hobby Dealer

GPMA2426 ......W

ING JOINERS

(2) ........Contact Your Hobby Dealer

GPMA2427 ......380 

MOTOR

..................Contact Your Hobby Dealer

GPMA2428 ......F

LAPERON MIXER

..........Contact Your Hobby Dealer

GPMA2429 ......S

PEED CONTROL

...........Contact Your Hobby Dealer

Part # 

Description

How to Purchase

GPMA2430 ......D

ECAL SET

...................Contact Your Hobby Dealer

GPMA2431 ......B

ATTERY PACK

..............Contact Your Hobby Dealer

GPMA2432 ......C

ANOPY

.......................Contact Your Hobby Dealer

GPMA2433 ......P

ROPELLER

..................Contact Your Hobby Dealer

Missing pieces ...........Contact Product Support
Instruction manual .....Contact Product Support
Full-size plans ............Not available

Kit Contents (Photographed)

1. Left Wing Panel

6. Wing Joiner Tubes

2. Right Wing Panel

7. Motor

3. Wing Tips (2)

8. Propellers

4. Plastic Center Section

9. Tape

5. Plastic Canopy

10. Ailevators

Kit Contents (Not Photographed)

Nylon Control Horns (2)

2-56 x 1/2” Machine Screw (4)

12” Pushrods (2)

Nylon Clevis (2)

Nylon Tie Strap (1)

Silicone Retainer (2)

Hook and Loop Tape (1)

Summary of Contents for Slinger GPMA1180













Reviews: