background image

INSTRUCTION MANUAL

Wingspan: 35.5 in [900mm]
Wing Area: 389 in

2

 [25.1dm

2

]

Weight: 21.1 – 26.3 oz [595 – 745g]
Wing Loading: 7.8 – 9.7 oz/ft

2

 [24 – 30g/dm

2

]

Length: 25 in [630mm]
Radio:   4-channel, 4 micro servos
Motor: RimFire

 400 (28-30-950) brushless 

ESC:  

ElectriFly

 SS-25

Battery:   11.1V (3S) 1250mAh – 1500mAh

Great Planes

®

 Model Manufacturing Co. guarantees this kit to be 

free from defects in both material and workmanship at the date 
of purchase. This warranty does not cover any component parts 
damaged by use or modifi cation.  In no case shall Great Planes’ 
liability exceed the original cost of the purchased kit.
 Further, 
Great Planes reserves the right to change or modify this warranty 
without notice.

In that Great Planes has no control over the fi nal assembly or 
material used for fi nal assembly, no liability shall be assumed nor 
accepted for any damage resulting from the use by the user of 
the fi nal user-assembled product. By the act of using the user-
assembled product, the user accepts all resulting liability.

If the buyer is not prepared to accept the liability associated 
with the use of this product, the buyer is advised to return 
this kit immediately in new and unused condition to the place
of purchase.

To make a warranty claim send the defective part or item to Hobby 
Services at the address below:

Hobby Services

3002 N. Apollo Dr., Suite 1

Champaign, IL 61822 USA

Include a letter stating your name, return shipping address, as 
much contact information as possible (daytime telephone number, 
fax number, e-mail address), a detailed description of the problem 
and a photocopy of the purchase receipt. Upon receipt of the 
package the problem will be evaluated as quickly as possible.

READ THROUGH THIS MANUAL BEFORE STARTING CONSTRUCTION. IT CONTAINS IMPORTANT 
INSTRUCTIONS AND WARNINGS CONCERNING THE ASSEMBLY AND USE OF THIS MODEL.

Champaign, Illinois

(217) 398-8970, Ext 5

airsupport@greatplanes.com

Entire Contents © Copyright 2008

GPMA1144MNL  V1.0

WARRANTY

Summary of Contents for SopWith Camel

























Reviews: