background image

WARRANTY

Great Planes

®

Model Manufacturing Co.

guarantees this kit to be free from defects in both material and workmanship at the date of

purchase. This warranty does not cover any component parts damaged by use or modification. 

In no case shall Great Planes’

liability exceed the original cost of the purchased kit.

Further, Great Planes reserves the right to change or modify this warranty

without notice.

In that Great Planes has no control over the final assembly or material used for final assembly, no liability shall be assumed nor
accepted for any damage resulting from the use by the user of the final user-assembled product. By the act of using the user-assembled
product, the user accepts all resulting liability.

If the buyer is not prepared to accept the liability associated with the use of this product, the buyer is advised to return this
kit immediately in new and unused condition to the place of purchase.

While this kit has been flight tested to exceed normal use, if the plane will be used for extremely high stress flying, such as racing, the
modeler is responsible for taking steps to reinforce the high stress points.

READ THROUGH THIS MANUAL BEFORE
STARTING CONSTRUCTION. IT CONTAINS
IMPORTANT WARNINGS AND INSTRUCTIONS
CONCERNING THE ASSEMBLY AND USE OF
THIS MODEL.

Manual GPMZ0211 For Kit GPMA1300  V1.0

© Copyright 1998  

P.O. Box 788

Urbana, IL 61803

(217) 398-8970

www.greatplanes.com

INSTRUCTION MANUAL

Almost Ready-to-Fly

Summary of Contents for spacewalker

























Reviews: