A building stand or cradle comes in handy during the build. We
use the Robart Super Stand II (ROBP1402) for all our projects
in R&D, and it can be seen in pictures throughout this manual.
The Super Skybolt ARF does not include a pilot figure. If you
plan to install one, the pilot can be attached during the build,
or later on since the canopy is removable. We suggest using
the Great Planes pilot figure (GPMA2475).
This is the list of hardware and accessories required to finish the
Super Skybolt ARF. Order numbers are provided in parentheses.
❏
#64 Rubber bands (1/4 lb [113 g] box – HCAQ2020)
❏
3' [900mm] Standard silicone fuel tubing (GPMQ4131)
❏
R/C foam rubber (1/4" [6 mm] – HCAQ1000, or 1/2"
[13 mm] – HCAQ1050)
This is the list of Adhesives and Building Supplies that are
required to finish the Super Skybolt ARF.
❏
1/2 oz. [15g] Thin Pro
™
CA (GPMR6001)
❏
Pro 30-minute epoxy (GPMR6047)
❏
Drill bits: 1/16" [1.6 mm], 5/64" [2 mm], 3/32" [2.4 mm],
7/64" [2.8 mm] 11/64" [4.4 mm], 1/4" [6.4 mm]
❏
8-32 Tap and drill set (GPMR8103)
❏
Tap handle (GPMR8120)
❏
Stick-on segmented lead weights (GPMQ4485)
❏
#1 Hobby knife (HCAR0105)
❏
#11 Blades (5-pack – HCAR0211)
❏
Small T-pins (100 – HCAR5100)
❏
Denatured alcohol (for epoxy clean up)
❏
Hayes Small Clamp 1-3/8" [26 mm] (HAYR1104)
❏
Petroleum jelly
Here is a list of optional tools mentioned in the manual and
other items that will help you build the Super Skybolt ARF.
❏
Great Planes Heat-Shrink Tubing Assortment
(12 – GPMM1070)
❏
Top Flite
®
MonoKote
®
sealing iron (TOPR2100)
❏
Top Flite Hot Sock
™
iron cover (TOPR2175)
❏
Top Flite MonoKote trim seal iron (TOPR2200)
❏
Top Flite MonoKote heat gun (TOPR2000)
❏
Hobbico
®
60 watt soldering iron (HCAR0776)
❏
Pro 6-minute epoxy (GPMR6045)
❏
2 oz. [57 g] Spray CA activator (GPMR6035)
❏
4 oz. [113 g] Aerosol CA activator (GPMR634)
❏
CA applicator tips (HCAR3780)
❏
CA debonder (GPMR6039)
❏
Epoxy brushes (6 – GPMR8060)
❏
Mixing sticks (50 – GPMR8055)
❏
Mixing cups (GPMR8056)
❏
Builder’s Triangle Set (HCAR0480)
❏
36" Metal ruler (HCAR0475)
❏
Pliers with wire cutter (HCAR0630)
❏
Hobbico Duster
™
can of compressed air (HCAR5500)
❏
Masking tape (TOPR8018)
❏
Threadlocker
™
thread-locking compound (GPMR6060)
❏
Switch & Charge Jack Mounting Set (GPMM1000)
❏
Panel Line Pen (TOPQ2510)
❏
Rotary tool such as Dremel
®
❏
Rotary tool reinforced cut-off wheel (GPMR8200)
❏
Servo horn drill (HCAR0698)
❏
Dead Center
™
Engine Mount Hole Locator (GPMR8130)
❏
Precision Magnetic Prop Balancer (TOPQ5700)
❏
Prop Reamer (GPMQ5005)
•
There are two types of screws used in this kit:
•
Sheet Metal Screws (SMS) are designated by a
number and a length. For example #6 x 3/4" [19 mm]
This is a #6 screw that is 3/4" [19 mm] long.
•
Socket Head Cap Screws (SHCS) are designated by a
number, threads per inch, and a length. For example
4-40 x 1-1/2" [38 mm]
This is a number four screw that is 1-1/2" [38 mm] long
with forty threads per inch.
IMPORTANT BUILDING NOTES
Optional Supplies & Tools
Adhesives & Building Supplies
Required Hardware & Accessories
ADDITIONAL ITEMS REQUIRED
Pilot
Building Stand
4
