background image

5

MODEL INSPECTION

Before starting to build, inspect the parts to make sure they 
are of acceptable quality. If any parts are missing or are not of 
acceptable quality, or if you need assistance with assembly, 
contact 

Product Support

. When reporting defective or 

missing parts, use the part names exactly as they are written 
in the instruction manual.

Great Planes Product Support

3002 N Apollo Drive, Suite 1  Ph: (217) 398-8970, ext. 6
Champaign, IL 61822 

Fax: (217) 398-7721

E-mail: airsupport@greatplanes.com

ORDERING REPLACEMENT PARTS

Replacement parts for the Great Planes Ultra Sport .46/EP 
are available using the order numbers in the 

Replacement 

Parts List

 that follows. The fastest, most economical service 

can be provided by your hobby dealer or mail-order company. 
Not all parts are available separately (an aileron cannot be 
purchased separately, but is only available with the wing kit). 
Replacement parts are not available from Product Support, 
but can be purchased from hobby shops or mail order/Internet 
order fi rms. Hardware items (screws, nuts, bolts) are also 
available from these outlets.

To locate a hobby dealer, visit www.greatplanes.com and 

click on “Where to Buy”. Follow the instructions provided on 
the page to locate a U.S., Canadian or International dealer.

Order No.

Description

Wing

Fuselage

Tail Surface Set

Canopy/Hatch

Cowl

Landing Gear Leg Set L /R

Retracts Only Set

Retractable Landing Gear Set

Spinner

Tailwheel Set

Axle Set

Fuel Tank

EP Motor Mount Set

Decals

GPMA2015

GPMA2016

GPMA2017

GPMA2018

GPMA2019

GPMA2020

GPMA2021

GPMA2022

GPMA2023

GPMA2024

GPMA2025

GPMA2026

GPMA2027

GPMA2028

REPLACEMENT PARTS LIST

KIT CONTENTS

1.
2.
3.
4.
5.
6.
7.
8.
9.

10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.

Fuselage
Canopy/Hatch
Left Wing
Right Wing
Fuel Tank
Spinner
Belly Pan
Engine Mount
Vertical Fin
Rudder
Horizontal Stabilizer
Retracts
Tail Wheel
Main Wheels
Wing Joiner
Fuel Tank Tray
Forward Sub Tray
Forward Battery Tray
EP Motor Box Parts Set
Cowl

1

11

6

2

20

12

13

14

15

16

17

18

19

4

8

9

10

7

3

5

Summary of Contents for ULTRA SPORT 46

































Reviews: