Gree Versati II Series Service Manual Download

Page: 4 / 18

Test Operation & Troubleshooting & Maintenance

High pressure protection

High pressure

Low pressure protection

Low pressure

High discharge protection

Hi-discharge

Refrigerant loss protection

Refri-loss

Heat pump-water pump protection

HP-pump

Solar kit-water pump protection

SL-pump

Swimming pool-water pump protection

Swimming-pump

Incorrect capacity DIP switch setting

Capacity DIP

Communication error between indoor and outdoor unit

ODU-IDU Com.

Drive communication error

Drive com.

High pressure sensor error

HI-pre. sens.

Enthalpy-enhancing sensor error

En. senser

Low pressure sensor error

LOW-pre. Sens.

Heat exchanger-leaving water temperature sensor error

Temp-HELW

Auxiliary heater-leaving water temperature sensor error

Temp-AHLW

Heat exchanger-entering water temperature sensor error

Temp-HEEW

Water tank water temperature sensor 1 error

Tank sens. 1

Water tank water temperature sensor 2 error

Tank sens. 2

Solar kit-entering water temp sensor

T-SL water out

Solar kit-leaving water temp sensor

T-SL water in

Solar kit- temp sensor

T-Solar pannel

Swimming pool-entering water temp sensor

T-Swimming in

Swimming pool-leaving water temp sensor

T-Swimming out

Swimming pool-water temp sensor

T-Swimming

Remote room sensor 1

T-Remote Air1

Remote room sensor 2

T-Remote Air2

Heat pump-water flow switch

HP-Water SW

Solar kit-water flow switch

SL-Water SW

Swimming pool-water flow switch

SW-Water SW

Welding protection of the auxiliary heater 1

Auxi. heater 1

Welding protection of the auxiliary heater 2

Auxi. heater 2

Welding protection of the water tank heater

Auxi. -WTH

Under-voltage DC bus or voltage drop error

DC under-vol.

Over-voltage DC bus

DC over-vol.

AC current protection (input side)

AC curr. pro.

IPM defective

PFC defective

FPC defective

Start failure

Phase loss

Drive module resetting

Driver reset

Compressor over-current

Com. over-cur.

Overspeed

Sensing circuit error or current sensor error

Current sen.

Summary of Contents for Versati II Series



















Search results

Summary of Contents for Versati II Series

Reviews:

Related manuals for Versati II Series

Brands by name

Popular brands

Gree Versati II Series, Service Manual

Search results

Summary of Contents for Versati II Series

Reviews:

Related manuals for Versati II Series

Brands by name

Popular brands