Home
/
Green Hobby
/
Daisy E
/
Building Instructions

Green Hobby Daisy E, Building Instructions

The Green Hobby Daisy E is a remarkable DIY kit that allows you to build a stunning, eco-friendly daisy sculpture for your garden. Our detailed building instructions manual is available for free download from 88.208.23.73:8080, offering easy-to-follow steps to create this beautiful piece of art.

Share

1
2
3
4
5
6

Page: 6 / 6

background image

Glue in fin

Note location of cable drilling

Cable & fin finished

Another view …

Elevator cable installed

Elevator linkage from below

Servo bearers glued in

Bearer location from above

Servo & cable connectors

Propeller downthrust

Wing pin ready to glue

Wings finished

Canopy with epoxied-in wire

Bend the wire like this, to clip on canopy

«
...
4
5
6

Summary of Contents for Daisy E







Reviews:

No comments

Related manuals for Daisy E

Brand: Eclipse Pages: 16

Brand: Minicraft Models Pages: 4

Brand: Skippy Buddy Pages: 2

Brand: Fisher-Price Pages: 2

Lokpuffer Puff-H0

Brand: Fichtelbahn Pages: 2

Brand: LEGO Pages: 44

Brand: 4-Max Pages: 8

Ninjago Masters of Spinjitzu Wyplash 4645006

Brand: LEGO Pages: 2

Brand: PCM Pages: 13

Brand: MAC Rail Pages: 8

Brand: H-KING Pages: 12

Brand: Fisher-Price Pages: 6

Brand: Hot Wheels Pages: 4

Brand: Fisher-Price Pages: 10

Brand: Ripmax Pages: 12

Brand: LEGO Pages: 23

Brand: Ravensburger Pages: 28

Brand: Align Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands