background image

AMCA 5.2 Pressure Drop 

SMD-202

5D

6D

5D

D =

4  (W) (H)

3.14

Figure 5.3

Figure 5.2

Figure 5. 5

R

Greenheck Fan Corporation certifies that the 

model SMD-202 shown herein is licensed to bear 
the AMCA Seal. The ratings shown are based on 
tests and procedures performed in accordance 
with AMCA Publication 511 and comply with 

the requirements of the AMCA Certified Ratings 
Programs. The AMCA Certified Ratings Seal 

applies to air performance ratings only. 

Velocity (fpm) 

Pressure Drop  

(in. wg) 

Velocity (fpm) 

Pressure Drop  

(in. wg) 

Velocity (fpm) 

Pressure Drop  

(in. wg) 

Velocity (fpm) 

Pressure Drop  

(in. wg) 

500

0.04 

500

0.02 

500

0.01 

500

0.01 

1000 

0.14 

1000

0.07 

1000

0.04 

1000

0.06 

1500

0.31

1500

0.16

1500

0.09 

1500

0.13 

2000

0.55

2000

0.29

2000

0.16

2000

0.23 

2500   

0.86

2500

0.45

2500

0.25

2500

0.36 

3000

1.24

3000

0.65 

3000

0.36

3000

0.52

3500

1.69

3500

0.89

3500

0.49

3500

0.70 

4000

2.20

4000

1.16

4000

0.64

4000

0.92

12 in. x 12 in. (305mm x 305mm) 

24 in. x 24 in. (610mm x 610mm) 

36 in. x 36 in. (914mm x 914mm) 

12 in. x 48 in. (305mm x 1219mm) 

Velocity (fpm) 

Pressure Drop  

(in. wg) 

500

0.03 

1000

0.10

1500

0.23 

2000

0.41

2500

0.63

3000

0.91

3500

1.24

4000

1.62

48 in. x 12 in. (1219mm x 305mm) 

Summary of Contents for Smoke Dampers SMD-202








Reviews: