background image

HPB25 Hydraulic Paving Breaker

Greenlee Tools, Inc.

4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

3

IMPORTANT SAFETY INFORMATION

SAFETY 

ALERT 

SYMBOL

This symbol is used to call your attention to hazards 

or unsafe practices which could result in an injury or 

property damage. The signal word, defined below, 

indicates the severity of the hazard. The message 

after the signal word provides information for pre-

venting or avoiding the hazard.

Immediate hazards which, if not avoided, WILL result 

in severe injury or death.

Hazards which, if not avoided, COULD result in 

severe injury or death.

Hazards or unsafe practices which, if not avoided, 

MAY result in injury or property damage.

Read and understand all of the 

instructions and safety information 

in this manual before operating or 

 servicing this tool.
Failure to observe this warning 

could result in severe injury or death.

Skin injection hazard:
•  Do not use hands to check for 

leaks.

•  Do not hold hose or couplers 

while the hydraulic system is 

pressurized. 

•  Depressurize the hydraulic system 

before servicing.

Oil under pressure easily punc-

tures skin, causing serious injury, 

 gangrene, or death. If you are 

injured by escaping oil, seek medical 

 attention  immediately.

Do not exceed the following hydraulic power source 

maximums:
•  Hydraulic flow: 25 l/min (7 gpm)
•  Pressure relief: 207 bar (3000 psi)
•  Back pressure: 13.8 bar (200 psi)
Failure to observe this warning could result in severe 

injury or death.

Wear eye protection when operating 

or servicing this tool. 
Failure to wear eye protection could 

result in serious eye injury from 

flying debris or hydraulic oil. 

Wear hearing protection when using 

this tool. 
Failure to observe this warning 

could result in serious injury.

Wear foot protection when using this 

tool. 
Failure to observe this warning 

could result in serious injury.

Tool, bit, and other components may 

be hot during and after operation. 

Allow to cool before handling, or 

handle with heat-resistant gloves.
Failure to observe this warning 

could result in severe injury or death.

Do not disconnect tool, hoses or fittings while the 

power source is running or if the hydraulic fluid is 

hot. Hot hydraulic fluid can cause serious burns.

Summary of Contents for HPB25













Reviews:

Related manuals for HPB25