13
English (Original Instructions)
Greenworks tools' high standard for dependability, ease of
operation, and operator safety. When properly cared for,
it will give you years of rugged, trouble-free performance.
Read these instructions carefully, be familiar with the
Keep bystanders away
switched off, a rotating blade can
Keep supply flexible cord away from
■
■
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge,
■
■
■ Never operate the machine while people, especially
children, or pets are nearby.
■ Keep in mind that the operator or user is responsible
■
■
■ Before using, always visually inspect to see that the
blade, blade bolt and the blade assembly are not worn
■
damaged during use, disconnect the cord from the
supply immediately. DO NOT TOUCH THE CORD
BEFORE DISCONNECTING THE SUPPLY. Do not
OPERATION
■
Operate the machine only in daylight or in good
artificial light.
■
Avoid operating the machine in wet grass.
■
Always be sure of your footing on slopes.
■ Walk, never run.
■ Mow across the face of slopes, never up and down.
■
Exercise extreme caution when changing direction on
slopes.
■
Do not mow excessively steep slopes.
■
Use extreme caution when reversing or pulling the
machine towards you .
■
Stop the blade(s) if the machine has to be tilted for
transportation when crossing surfaces other than
grass, and when transporting the machine to and from
the area to be used.
■
Never operate the machine with defective guards
or shields, or without safety devices, for example
deflectors and/or grass collector, in place.
■
Switch on the motor carefully according to instructions
and with feet well away from the blade(s).
■ Do not tilt the machine when switching on the motor,
except if the machine has to be tilted for starting. In
this case, do not tilt it more than absolutely necessary
and lift only the part, which is away from the operator.
■
Do not start the machine when standing in front of the
discharge opening.
■
Do not put hands or feet near or under rotating parts.
Keep clear of the discharge opening at all times.
■
Do not transport the machine while the power source
is running.
■ Stop the machine, and remove plug from the socket.
Make sure that all moving parts have come to a
complete stop.
● whenever you leave the machine,
● before clearing blockages or unclogging chute,
● before checking, cleaning or working on the
machine,
●
after striking a foreign object. Inspect the machine
for damage and make repair before restarting and
operating the machine;
if the machine starts to vibrate abnormally (check
immediately)
● inspect for damage,
● replace or repair any damaged parts,
●
check for and tighten any loose parts.
MAINTENANCE AND STORAGE
■ Keep all nuts, bolts and screws tight to be sure the
machine is in safe working condition.
■
Check the grass collector frequently for wear or
deterioration.
■ On machines with multi blade, take care as rotating
one blade can cause other blades to rotate
■
Be careful during adjustment of the machine to prevent
entrapment of the fingers between moving blades and
fixed parts of the machine.
■
Always allow the machine to cool down before storing.
■ When servicing the blades be aware that, even though
the power source is switched off, the blades can still
be moved.
■
Replace worn or damaged parts for safety. Use only
genuine replacement parts and accessories.
RECOMMENDATION FOR CLASS II MACHINE
The machine should be supplied via a residual current
device (RCD) with a tripping current of not more than 30
mA.
ELECTRICAL SAFETY
■
Warning! Switch off, remove plug from mains
before adjusting, cleaning or if cable is cut,
damaged or entangled.
■
The blades continue to rotate for a few seconds after
the machine is switched off.
■
Caution
– do not touch the rotating blade.
Your machine is double insulated for safety and requires
no earth connection. The operating voltage is 220-240V
AC, 50 Hz. Only use approved extension cables.
Extension cords/leads should only be used if they comply
with H05VV-F, H05RN-F types or IEC type design (60227
IEC 53, 60245 IEC 57).
If you want to use an extension cable when operating your
product, only the following cable dimensions should be
used:
●
1.5 mm
2
: max. length 60 m
●
2.5 mm
2
: max. length 100 m
Note: If an extension cable is used it must be earthed
and connected through the plug to the earth cable of
your supply network in accordance with prescribed safety
regulations.
WARNING
Inadequate extension cables can be dangerous.
Extension cable, plug and socket must be of watertight
construction and intended for outdoor use.
