1
DESCRIPTION
1.1
PURPOSE
This machine is intended for cutting and trimming hedges and
bushes in domestic use. It is not intended to be used for
cutting above shoulder level.
1.2
OVERVIEW
Figure 1-7
1
Blade
2
Pivoting head
3
Pivoting button
4
Coupler
5
Safety lock button
6
Trigger
7
Rear handle
8
Battery release button
2
INSTALLATION
2.1
UNPACK THE MACHINE
WARNING
It is not necessary to assemble the machine.
•
If the parts have damage, do not use the machine.
•
If you do not have all the parts, do not operate the
machine.
•
If the parts are damaged or missing, speak to the service
center.
1. Open the package.
2. Read the documentation in the box.
3. Remove the machine from the box.
4. Discard the box and package in compliance with local
regulations.
2.1.1
FIT THE HEDGE TRIMMER HEAD
Figure 2
The hedge trimmer head can be mounted directly into handle
pole so as to achieve the standard length.
1. Insert the handle pole into the hedge trimmer head.
2. Slide the coupler upwards and turn it clockwise until it is
completely tightened.
NOTE
The maximum reach can be achieved by fitting the
extension tube between the handle pole and the hedge
trimmer head.
WARNING
Periodically check the connections to ensure that they are
tightened securely.
2.1.2
REMOVE THE HEDGE TRIMMER
HEAD
Figure 2
1. Rest the machine on the ground.
2. Loosen the couplers.
3. Take off the trimmer head / handle pole.
2.1.3
INSTALL THE BATTERY PACK
Figure 3
WARNING
•
If the battery pack or charger is damaged, replace the
battery pack or the charger.
•
Stop the machine and wait until the motor stops before
you install or remove the battery pack.
•
Read, know, and do the instructions in the battery and
charger manual.
1. Align the lift ribs on the battery pack with the grooves in
the battery compartment.
2. Push the battery pack into the battery compartment until
the battery pack locks into place.
3. When you hear a click, the battery pack is installed.
2.1.4
REMOVE THE BATTERY PACK
Figure 3
1. Push and hold the battery release button.
2. Remove the battery pack from the machine.
3
OPERATION
•
Touch the blade carefully.
•
Do not put your fingers into the notches or in position
where they can get cut.
•
Do not touch the blade unless you remove the battery
pack.
•
Do not use the machine if the blade is damaged or bent.
•
Remove all objects such as cords, lights, wire, or string
which can become entangled in the cutting blade and
create a risk of personal injury.
WARNING
If the blade jams on an electrical cord or line, DO NOT
TOUCH THE BLADE! IT CAN BE LIVE AND
DANGEROUS. Do the steps below:
1. Hold the insulated rear handle or put the machine down
and away from you.
2. Disconnect the electrically service to the damaged line
or cord before you try to free the blade.
3.1
START THE MACHINE
Figure 4.
4
English
EN
Summary of Contents for G24PH51
