4.7
ADJUST THE CUTTING
DIAMETER
Figure 10.
NOTE
The machine is set at a 35.6 cm cutting diameter. You can
adjust to a 40.6 cm cutting diameter.
Set the cutting diameter to 35.6 cm for greater runtime and
40.6 cmfor a larger cutting area.
1. Remove the battery pack.
2. Remove the blade screws from the cut-off blade.
3. Turn the cut-off blade 180°.
4. Tighten the blade screws.
4.8
USE THE SHOULDER STRAP
Figure 11.
1. Attach the carabiner to the carrying ring on the pole.
2. Put on the shoulder strap.
3. Adjust the length of the strap so that the carabiner is
about the width of a hand below your right hip.
5
MAINTENANCE
IMPORTANT
Read and understand the safety regulations and the
maintenance instructions before you clean, repair or do the
maintenance work on the machine.
IMPORTANT
Make sure that all nuts, bolts and screws are tight. Examine
regularly that you install the handles tightly.
IMPORTANT
Use only the replacement parts and accessories of the initial
manufacturer.
5.1
GENERAL INFORMATION
IMPORTANT
Only your dealer or approved service center can do the
maintenance that is not given in this manual.
Before the maintenance operations:
•
Stop the machine.
•
Remove the battery pack.
•
Cool the motor.
•
Store the machine in cool and dry place.
•
Use correct clothing, protective gloves and safety glasses.
5.2
CLEAN THE MACHINE
•
Clean the machine after use with a moist cloth dipped in
neutral detergent.
•
Do not use aggressive detergents or solvents to clean the
plastic parts or handles.
•
Keep the trimmer head free of grass, leaves, or excessive
grease.
•
Keep the air vents clean and free of debris to avoid
overheating and damage to the motor or the battery.
•
Do not spray water onto the motor and electrical
components.
5.3
REMOVE ANY REMAINING LINE
Figure 12 - 15.
1. Push the tabs on the sides of the trimmer head at the same
time.
2. Remove the spool cover and the spool.
3. Remove any remaining line.
4. Put the spool in the spool housing.
5. Install the spool cover onto the trimmer head.
6. Push the spool cover until it clicks into position.
5.4
INSTALL THE CUTTING LINE
Figure 16 - 18.
NOTE
Do not put more than 15 feet of cutting line in at a time.
1. Line up the slots on the spool cap with the slots on the
trimmer head.
2. Put the cutting line through the hole. Push the cutting line
until it exits the opposite hole.
3. Pull the cutting line through until there is an equal
quantity of cutting line on each side.
4. Turn the spool cap clock-wise to wind the cutting line
into the trimmer head. Keep approximately 5 in of cutting
line above out of each side of the trimmer head.
5.5
REMOVE THE TRIMMER HEAD
Figure 19 - 20.
1. Put the metal rod in the specified angle transmission hole
to fix the trimmer head.
2. Turn the trimmer head clockwise to loosen it. Do not
remove the spacer from the shaft.
5.6
ASSEMBLE THE TRIMMER HEAD
Figure 21.
1. Put the metal rod in the specified angle transmission hole
to fix the trimmer head.
2. Assemble the trimmer head.
6
English
EN
Summary of Contents for GD60LT
Page 2: ......
Page 56: ...1 2 3 4 5 6 5 4 16 18 5 1 2 3 4 5 5 5 19 20 1 2 5 6 21 1 2 3 4 6 6 1 6 2 7 1 2 1 2 56 RU...
Page 137: ...3 3 3 1 2 3 4 5 3 4 4 1 2 3 4 3 5 5 1 2 3 3 6 5 1 2 4 4 1 6 1 2 1 2 4 2 6 1 4 3 7 4 4 8 137 BG...
Page 139: ...1 2 3 4 5 6 5 4 16 18 15 1 2 3 4 5 5 5 19 20 1 2 5 6 21 1 2 3 4 6 6 1 6 2 7 1 2 1 2 139 BG...
