Greystone Energy Systems GDT Series Installation Instructions Manual Download

Page: 11 / 18

Page 11

Alarm 2

Hyst 20

Alarm 2

Dly 2Min

Alarm 2

Hyst 0.5

Press the <UP> or <DOWN> to change the Alarm2 Hysteresis

within the limits. If Alarm2 is assigned to CO the range is 10

to 100 ppm in 5 ppm increments. The default is 20 ppm. If

Alarm2 is assigned to NO

the range is 0.5 to 2.0 ppm in 0.5 ppm

increments. The default is 0.5 ppm.

Use <UP> or <DOWN> to change the Alarm 2 Delay time within

the limits. The delay time may be set from 0 to 10 minutes in

1-minute increments. The default is 2 minutes.

Only if

Relay2

is installed

23. ALARM 2

HYSTERESIS

24. ALARM 2

DELAY

<MENU>

Press to advance to next menu item

<MENU>

Press to advance to next menu item

Relay 2

Direct

Relay 2

Test OFF

TestMode

Disable

Use <UP> or <DOWN> to toggle the available options. Relay

2 operation may be set to Direct or Reverse. Direct operation

means the relay is normally not energized and will energize on

an alarm condition (the NO/NC PCB designations are correct).

Reverse operation means the relay is normally energized

and will de-energize on an alarm condition (the NO/NC PCB

designations are reversed). Reverse operation can be used for

‘Fail Safe’ operation as the relay will change state on power loss.

The default is Direct.

Use <UP> or <DOWN> to toggle relay2 ON or OFF to test the

relay operation. Press <MENU> to reset to OFF.

Use <UP> or <DOWN> to disable or enable the test mode. The

default is Disable. When disabled, the front panel TEST switch

or TEST input will not initiate the test function. When enabled,

pressing the TEST switch will initiate the test function. Note that

the test mode will only function is the device is operating in the

Normal mode, the test function cannot be initiated if any alarm

is present.

25. RELAY 2

DIRECT/

REVERSE

26. RELAY 2

TEST

27. RELAY 2

TEST MODE

<MENU>

Press to advance to next menu item

<MENU>

Press to advance to next menu item

<MENU>

Press to advance to next menu item

Only if

Relay2 Test Mode

is enabled

TestMode

Time 5

Use <UP> or <DOWN> to change the test mode time within the

limits. The test mode operating time may be set from 1 to 15

minutes in 1-minute increments. The default is 5 minutes. This

item sets how long the test mode will operate when the TEST

switch is pressed.

28. RELAY 2

TEST MODE

TIME

<MENU>

Press to advance to next menu item

IN-GE-GDTXXX-06

Summary of Contents for GDT Series



















Search results

Summary of Contents for GDT Series

Reviews:

Related manuals for GDT Series

Brands by name

Popular brands

Greystone Energy Systems GDT Series, Installation Instructions Manual

Search results

Summary of Contents for GDT Series

Reviews:

Related manuals for GDT Series

Brands by name

Popular brands