background image

Page  7

SPECIFICATIONS

PM Sensor

Sensor ............................................Laser scatter method

Particle Size ..................................PM1.0, PM2.5, PM4.0, or PM10 (selectable)

Mass Concentration ..................0 to 1000 ug/m

3

Resolution ....................................1 ug/m

3

Accuracy .......................................±10 ug/m

3

 (0 to 100 ug/m

3

), ±10% (100 to 1000 ug/m

3

)

Response Time ...........................1 second

Sensor Lifetime ..........................>8 years

Analog Model

Consumption ..............................75 mA max @ 24 Vdc, 100 mA max @ 24 Vac

Output Signals ............................4-20 mA (sourcing) or 0-5 Vdc / 0-10 Vdc (selectable)

Output Drive Capability ..........

Current:

 550Ω max

 

Voltage:

 5,000Ω min

Output Scale ...............................0 to 1000 ug/m

3

 (menu selectable)

BACnet® Model

Consumption ..............................50 mA max @ 24 Vdc, 80 mA max @ 24 Vac

Interface ........................................MS/TP, 2-wire RS-485

Baud Rate .....................................9600, 19200, 38400, 57600, 76800 or 115200 (menu selectable)

Address Range ............................0 to 127 (menu selectable)

Modbus Model

Consumption ..............................50 mA max @ 24 Vdc, 80 mA max @ 24 Vac

Interface ........................................MS/TP, 2-wire RS-485, RTC

Baud Rate .....................................9600, 19200, 38400, 57600, 76800 or 115200 (menu selectable)

Address Range ............................1 to 255 (menu selectable)

Tri-Color LED (optional)

Good ..............................................Green (0 to 50 ug/m

3

)

Moderate ......................................Yellow (51 to 150 ug/m

3

)

Poor ................................................Red (151 to 1000 ug/m

3

PM Alarm Relay (optional)

Contact Ratings ..........................Form C (N.O. + N.C.), 2A @ 140 Vac, 2A @ 30 Vdc

Relay Se Hysteresis ...Programmable via menu

Relay Time Delay ........................Programmable via menu

General

LCD Size ........................................35mm W x 15mm H (1.4" x 0.6") alpha-numeric 2 line x 8 characters

LCD Backlight ..............................Enable or disable via menu

Display Values .............................0 to 500 Air Quality Index or 0 to 1000 ug/m

3

Power Supply ..............................24 Vac/dc ±20% (non-isolated half-wave rectified)

Protection Circuitry ...................Reverse voltage protected, over-voltage protected

Operating Conditions ..............0 to 50°C (32 to 122°F), 20 to 80 %RH non-condensing

Storage Conditions ...................-30 to 60°C (-22 to 140°F)

Wiring Connections ..................Screw terminal block (14 to 22 AWG)

Enclosure Dimensions .............84mm W x 117mm H x 29mm D (3.3" x 4.6" x 1.15")

Enclosure Material .....................White ABS, IP30 (NEMA 1)

Weight ...........................................5.3 oz (150 gm)

Country of Origin .......................Canada

Accessories

PMFRSM ..........................................Replaceable sensor module and wire harness

84 mm

3.3“

119 mm

4.7“

29 mm

1.15 “

82.6 mm

3.25 “

58 mm

2.3 “

DIMENSIONS

IN-GE-PMRMCXXX-05

Copyright © Greystone Energy Systems, Inc.   All Rights Reserved    Phone:  +1 506 853 3057  Web: www.greystoneenergy.com

Summary of Contents for PMRMC Series









Reviews: