background image

Manual CC2 © Grimm Audio

5

does not fit into your outlet, consult an electrician
for replacement of the obsolete outlet.

8.

Protect the power cord from being walked on or
pinched, particularly at plugs, convenience
receptables, and the point where they exit from the
apparatus.

9.

Unplug this apparatus during lightning storms or
when unused for long periods of time.

10. Do not use this apparatus near water.

11. Do not use this apparatus outside.

12. Do not expose the apparatus to dripping or

splashing. Do not place objects filled with liquids
(flower vases, drink cans, coffee cups, etc) on the
apparatus.

13. Clean only with a dry, soft, non-fluffy cloth. Do not

spray any liquid cleaner onto the cabinet, as this
may lead to dangerous shocks. Do not spray any

liquid cleaner onto the faceplate, as this may
damage the front panel.

14. Install in accordance with the manufacturer’s

instructions.

15. Do not install near any heat sources such as

radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat. Avoid
exposure to direct sunlight.

16. Use only attachments or accessories specified by

the manufacturer.

17. Use only with a cart, stand, bracket, or table

designed for use with professional audio or music
equipment. In any installation, make sure that injury
or damage will not result from cables pulling on the
apparatus and its mounting. If a cart is used, use
precaution when moving the cart/apparatus
combination to avoid injury from tip-over.

2.

Im

po

rta

nt

Sa

fe

ty

In

str

uc

tio

ns

Summary of Contents for CC2



















Reviews: