background image

Operator Manual

Grindmaster-Cecilware

4003 Collins Lane, Louisville, KY 40245 USA 
Phone: 502.425.4776 Toll Free: 800.695.4500
Fax: 502.425.4664
Web: gmcw.com  Email: info@gmcw.com

Safety Information........................2
Specifications.................................3
Installation and Set-Up.................4
Product Preparation & Use...........7

Daily Cleaning ...............................8
Troubleshooting ..........................11
Basic Machine Parts ....................14

Thank you for purchasing this quality cold beverage dispenser. For your safety and the safety of
others, read all warnings and the operator’s manual before installing or using the product. Properly
instruct all operators. Keep training records. For future reference, record serial number here:

Table of Contents

Simplicity

Bubbler

Crathco

®

Cold Beverage Dispensers

Grindmaster-Cecilware provides the industry’s
BEST warranty. Visit gmcw.com for warranty
terms and conditions.

Model CS-2D-16

Model CS-2E-16

©2017 Grindmaster-Cecilware

Printed in Thailand

0917 Form # CC-330-05

Part # 390-00003

(cULus certification applies only to
United States and Canada models.)

Model CS-3L-16

Activate your warranty now at

http://gmcw.com/warranty-registration

Summary of Contents for Crathco CS-2D-16





















Reviews: