G0513X/G0514X/G0514X3 Extreme Series Bandsaw
-13-
Additional Safety Instructions for Bandsaws
7. BLADE SPEED.
Allow blade to reach full
speed before cutting.
8. LEAVING WORK AREA.
Never leave a
machine running and unattended. Allow the
bandsaw to come to a complete stop be-
fore you leave it unattended.
9. FEED RATE.
Always feed stock evenly
and smoothly.
DO NOT force or twist blade
while cutting, especially when sawing small
radii.
10. WORKPIECE MATERIAL.
This machine
is designed to cut wood only. It is not
designed to cut metal or use cutting fluid.
11. MAINTENANCE/SERVICE.
All inspec-
tions, adjustments, and maintenance are
to be done with the power
OFF
and the
plug removed from the outlet. Wait for all
moving parts to come to a complete stop.
12. BLADE CONTROL.
Do not attempt to
stop or slow the blade with your hand or
a workpiece. Allow the blade to stop on its
own, unless your machine is equipped with
a brake.
13. EXPERIENCING DIFFICULTIES.
If at
any time you are experiencing difficulties
performing the intended operation, stop
using the machine! Contact our Technical
Support Department at (570) 546-9663.
1. BLADE CONDITION.
Do not operate with
dull, cracked or badly worn blade.
Dull
blades require more effort to use and are
difficult to control. Inspect blades for cracks
and missing teeth before each use, and
replace as required.
2. HAND PLACEMENT.
Never position fin-
gers or thumbs in line with the cut.
Serious
personal injury could occur.
3. GUARDS.
Do not operate this bandsaw
without the blade guard in place or with the
doors open.
4. BLADE REPLACEMENT.
When replacing
blades, make sure teeth face toward the
workpiece and the blade is properly ten-
sioned before operating.
5. WORKPIECE HANDLING.
Never hold
small workpieces with your fingers during
a cut. Always support/feed the workpiece
with push stick, table support, vise, or
some type of clamping fixture.
6. CUTTING TECHNIQUES.
Plan your cuts
so you always cut out of the wood. DO
NOT back the workpiece away from the
blade while the saw is running. If you need
to back the work out, turn the bandsaw
OFF
and wait for the blade to come to a
complete stop, and DO NOT twist or put
excessive stress on the blade while back-
ing work away.
No list of safety guidelines can be complete.
Every shop environment is different. Always
consider safety first, as it applies to your
individual working conditions. Use this and
other machinery with caution and respect.
Failure to do so could result in serious per-
sonal injury, damage to equipment, or poor
work results.
Like all machinery there is potential danger
when operating this machine. Accidents are
frequently caused by lack of familiarity or
failure to pay attention. Use this machine
with respect and caution to lessen the pos-
sibility of operator injury. If normal safety
precautions are overlooked or ignored, seri-
ous personal injury may occur.
Summary of Contents for EXTREME G0513X
